HP HPE FlexFabric 5930 Installation Manual Download Page 64

Page: 64 / 73

Table 23 System status LED description

LED mark

Status

Description

SYS

Steady green

The switch is operating correctly.

Flashing green

The switch is performing power-on self test (POST).

Steady red

The system has failed to pass POST or has problems such as fan failure.

Flashing red

Some ports have failed to pass POST.

Off

The switch is powered off or has failed to start up.

SFP+ port LED

Each SFP+ port has a status LED to show port operating status and activities.

Table 24 SFP+ port LED description

LED status

Description

Steady green

A transceiver module or cable has been correctly installed. The port has a link and is
operating at 10 Gbps.

Flashing green

The port is sending or receiving data at 10 Gbps.

Steady yellow

A transceiver module or cable has been correctly installed. The port has a link and is
operating at 1 Gbps.

Flashing yellow

The port is sending or receiving data at 1 Gbps.

Off

No transceiver module or cable has been installed or no link is present on the port.

QSFP+ port LED

Each QSFP+ port has a status LED to show port operating status and activities.

Table 25 QSFP+ port LED description

LED status

Description

Steady green

A transceiver module or cable has been correctly installed. The port has a link
and is operating at 40 Gbps.

Flashing green

The port is sending or receiving data at 40 Gbps.

Steady yellow

A transceiver module or cable has been correctly installed. The port has a link
and is operating at 10 Gbps.

Flashing yellow

The port is sending or receiving data at 10 Gbps.

Off

No transceiver module or cable has been installed or no link is present on the
port.

Management Ethernet port LEDs

The HPE 5930-32 QSFP+/HPE 5930-32 QSFP+ TAA/HPE 5930-4Slot/HPE 5930-4Slot TAA
switches provide a LINK LED and an ACT LED for the management Ethernet port.

Summary of Contents for HPE FlexFabric 5930










































































Search results

Summary of Contents for HPE FlexFabric 5930

Reviews:

Related manuals for HPE FlexFabric 5930

Brands by name

Popular brands

HP HPE FlexFabric 5930, Installation Manual

Search results

Summary of Contents for HPE FlexFabric 5930

Reviews:

Related manuals for HPE FlexFabric 5930

Brands by name

Popular brands