manualshive.com logo in svg

HP Fabric OS 7.0.0, Troubleshooting Manual, Page: 79 / 138

Share
Download
HP Fabric OS 7.0.0 Troubleshooting Manual Download Page 79

Fabric OS Troubleshooting and Diagnostics Guide

59

53-1002150-02

Considerations for downgrading firmware

5

Message

The FS8-18 (type 43) blade is not supported by the target firmware. Please use slotshow to find out 
which slot it is in and remove it first.

Probable cause and recommended action

The firmware download operation was attempting to downgrade a system to Fabric OS v6.1.1_enc 
or earlier with one or more Brocade FC8-18 AP blades (blade ID 43) in the system. Brocade 
Encryption Blade FC8-18 AP blades are not supported on firmware v6.1.1 or earlier, so the 
firmware download operation failed. 

Use the slotShow command to display which slots the Brocade FC8-18 AP blades occupy. Physically 
remove the blades from the chassis, or use the micro-switch to turn the blade off. Retry the 
firmware download operation.

Firmware versions

These messages refer to differences between the current firmware and the firmware you are 
applying to the switch.

Message

Cannot upgrade directly to v6.3.0. Upgrade your switch to v6.2.0 first before upgrading to the 
requested version.

Probable cause and recommended action

If the switch is running v6.1.0 or earlier, you are not allowed to upgrade directly to v6.3.0 because 
of the “two-version” rule.

Upgrade your switch to Fabric OS version v6.2.0 before upgrading to v6.3.0

Message

Non-disruptive firmwaredownload is not supported when downgrading to 6.1. Please use 
firmwaredownload -s to download the 6.1 firmware.

Probable cause and recommended action

If the switch is running v6.2.0, you are not allowed to downgrade directly to v6.1.x without causing 
disruption to your fabric. 

Downgrade using the firmwareDownload -s command. For more information on using this 
command, refer to the 

Fabric OS Administrator’s Guide

.

Message

Firmwaredownload of blade application firmware failed. Reissue firmwareDownload to recover.

Probable cause and recommended action

The firmware download operation was attempting to upgrade the SAS image while the blade was 
operational.

Retry the firmwareDownload command again.

Platform

This message pertains to switch features or fabric-wide settings that must be removed or disabled 
before downgrading the firmware.

Summary of Contents for Fabric OS 7.0.0











































































































































Reviews:

No comments