HP dc7700 - Convertible Minitower PC Troubleshooting Manual Download

Page: 59 / 72

Control panel message

Description

Recommended action

512-Chassis, Rear Chassis, or Front Chassis
Fan not Detected

Chassis, rear chassis, or front chassis fan is
not connected or may have malfunctioned.

Reseat chassis, rear chassis, or front
chassis fan.

Reseat fan cable.

Replace chassis, rear chassis, or front
chassis fan.

514-CPU or Chassis Fan not Detected

CPU or chassis fan is not connected or may
have malfunctioned.

Reseat CPU or chassis fan.

Reseat fan cable.

Replace CPU or chassis fan.

601-Diskette Controller Error

Diskette controller circuitry or floppy drive
circuitry incorrect.

Run Computer Setup.

Check and/or replace cables.

Clear CMOS. (See Appendix B,

Password Security and Resetting
CMOS on page 60

Replace diskette drive.

Replace the system board.

605-Diskette Drive Type Error

Mismatch in drive type.

Run Computer Setup.

Disconnect any other diskette controller
devices (tape drives).

Clear CMOS. (See Appendix B,

Password Security and Resetting
CMOS on page 60

610-External Storage Device Failure

External tape drive not connected.

Reinstall tape drive or press

and allow

system to reconfigure without the drive.

611-Primary Floppy Port Address
Assignment Conflict

Configuration error.

Run Computer Setup and check the
configuration in

Advanced

Onboard

Devices

660-Display cache is detected unreliable

Integrated graphics controller display cache
is not working properly and will be disabled.

Replace system board if minimal graphics
degrading is an issue.

912-Computer Cover Has Been Removed
Since Last System Startup

Computer cover was removed since last
system startup.

No action required.

917-Front Audio Not Connected

Front audio harness has been detached or
unseated from motherboard.

Reconnect or replace front audio harness.

918-Front USB Not Connected

Front USB harness has been detached or
unseated from motherboard.

Reconnect or replace front USB harness.

921-Device in PCI Express slot failed to
initialize

There is an incompatibility/problem with this
device and the system or PCI Express Link
could not be retrained to an x1.

Try rebooting the system. If the error
reoccurs, the device may not work with this
system

Table A-1

Numeric Codes and Text Messages (continued)

ENWW

POST Numeric Codes and Text Messages

Summary of Contents for dc7700 - Convertible Minitower PC









































































Search results

Summary of Contents for dc7700 - Convertible Minitower PC

Reviews:

Related manuals for dc7700 - Convertible Minitower PC

Brands by name

Popular brands

HP dc7700 - Convertible Minitower PC, Troubleshooting Manual

Search results

Summary of Contents for dc7700 - Convertible Minitower PC

Reviews:

Related manuals for dc7700 - Convertible Minitower PC

Brands by name

Popular brands