HP Compaq SP750 Page 56 Maintenance And Service Manual Download

Page: 56 / 132

Removal and Replacement Procedures

4-15

Diskette Drive

IMPORTANT:

Before beginning the removal procedure, be sure there is no diskette in the drive.

To remove the diskette drive:

Perform the steps in the “Service Preparations” section in this chapter, then place the
workstation on its side.

CAUTION:

Before removing the side access panel, ensure that the workstation is turned off, all

cables are disconnected from the back of the workstation, and the power cord is disconnected
from the grounded AC outlet.

Remove the following components:

Side access panel

Front bezel

Disconnect the cables from the back of the diskette drive.

Figure 4-12. Disconnecting the cables from the diskette drive

Summary of Contents for Compaq SP750





































































































































Search results

Summary of Contents for Compaq SP750

Reviews:

Related manuals for Compaq SP750

Brands by name

Popular brands

HP Compaq SP750, Maintenance And Service Manual

Search results

Summary of Contents for Compaq SP750

Reviews:

Related manuals for Compaq SP750

Brands by name

Popular brands