HP Compaq NX9000 Reference Manual Download Page 94

Page: 94 / 121

Troubleshooting and Maintenance

Configuring Your Notebook

Reference Guide

Main Menu

Setting

Description

Default

BIOS Revision

Shows the current BIOS version.

Detected
automatically

System Time

Sets the time using 24-hour format. Values set take
effect immediately.

System Date

Sets the date using dd/mm/yy format (except English,
which uses mm/dd/yy format).

Language

Sets the language for BIOS Setup.

Detected
automatically

Internal Hard Disk

Sets the hard drive type and various parameters.

Detected
automatically

UMA Video Memory

Sets the video memory size allocated from total
installed memory (RAM).

Auto

Memory

Shows the extended memory size.

Detected
automatically

Serial Number

Displays the serial number as shown on the back of
the unit.

Detected
automatically

Service ID

Displays an identifier used for repair service.

Detected
automatically

UUID

Displays the value of the 16-byte UUID (Universally
Unique ID) as 32 hex characters.

Detected
automatically

MAC Address

Displays the MAC network address of the internal
(wired) LAN.

Detected
automatically

Summary of Contents for Compaq NX9000


























































































































Search results

Summary of Contents for Compaq NX9000

Reviews:

Brands by name

Popular brands

HP Compaq NX9000, Reference Manual

Search results

Summary of Contents for Compaq NX9000

Reviews:

Brands by name

Popular brands