HP Compaq dx7400 Series Troubleshooting Manual Download Page 46 | Manualshive

Page: 46 / 69

background image

Solving CD-ROM and DVD Problems

If you encounter CD-ROM or DVD problems, see the common causes and solutions listed in the
following table or to the documentation that came with the optional device.

Table 2-15

Solving CD-ROM and DVD Problems

System will not boot from CD-ROM or DVD drive.

Cause

Solution

The device is attached to a SATA port that has been hidden in
the Computer Setup utility.

Run the Computer Setup utility and ensure

Device Available

is selected for the device's SATA port in

Security

>

Device

Security

.

Removable Media Boot is disabled in the Computer Setup
utility.

Run the Computer Setup utility and enable booting to
removable media in

Storage

>

Storage Options

. Ensure CD-

ROM is enabled in

Storage

>

Boot Order

.

Network Server Mode is enabled in Computer Setup.

Run the Computer Setup utility and disable Network Server
Mode in

Security

>

Password Options

.

Non-bootable CD in drive.

Try a bootable CD in the drive.

Boot order not correct.

Run the Computer Setup utility and change boot sequence in

Storage

>

Boot Order

.

Drive not found (identified).

Cause

Solution

Cable could be loose.

Check cable connections.

The system may not have automatically recognized a newly
installed device.

See reconfiguration directions in the

Solving Hardware

Installation Problems on page 32

section. If the system still

does not recognize the new device, check to see if the device
is listed within Computer Setup. If it is listed, the probable
cause is a driver problem. If it is not listed, the probable cause
is a hardware problem.

If this is a newly installed drive, run the Computer Setup utility
and try adding a POST delay under

Advanced

>

Power-On

.

The device is attached to a SATA port that has been hidden in
Computer Setup.

Run the Computer Setup utility and ensure

Device Available

is selected for the device's SATA port in

Security

>

Device

Security

.

Drive responds slowly immediately after power-up.

Run Computer Setup and increase the POST Delay in

Advanced

>

Power-On Options

.

CD-ROM or DVD devices are not detected or driver is not loaded.

Cause

Solution

Drive is not connected properly or not properly configured.

See the documentation that came with the optional device.

Movie will not play in the DVD drive.

Cause

Solution

Movie may be regionalized for a different country.

See the documentation that came with the DVD drive.

Decoder software is not installed.

Install decoder software.

40

Chapter 2 Troubleshooting Without Diagnostics

ENWW

«
...
44
45
46
47
48
...
»

Summary of Contents for Compaq dx7400 Series






































































Reviews:

No comments

Related manuals for Compaq dx7400 Series

Brand: NComputing Pages: 16

PowerBox 310 Series

Brand: Spectra Pages: 116

Brand: Gateway Pages: 182

Brand: C&T Pages: 73

Brand: Kettler Pages: 44

Brand: OEM Tools Pages: 4

Brand: IBM Pages: 194

Brand: Lenze Pages: 68

Brand: Gateway Pages: 346

Brand: easescreen Pages: 4

Brand: Clarke Pages: 8

Brand: MSI Pages: 29

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

VGC-VA10G - VAIO VA TV-PC

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands