manualshive.com logo in svg

HP Compaq dx6100 MT, Reference Manual

Share
Download
HP Compaq dx6100 MT Reference Manual Download Page 196

C–4

361293-003

Service Reference Guide, dx6100

605-Diskette Drive Type 

Error

Mismatch in drive type.

Run Computer Setup (F10 Setup).
Disconnect any other diskette controller 

devices (tape drives).
Clear CMOS.

912-Computer Cover 

Has Been Removed 

Since Last System Start 

Up

No action required.

917-Front Audio not 

Detected

Front audio harness has 

been detached or 

unseated from the system 

board.

Reconnect or replace front audio 

harness.

919-Front Panel, 

MultiPort, and/or 

MultiBay Risers not 

Detected.

Riser card has been 

removed or has not been 

reinstalled properly in the 

system.

Unplug computer and install/reinstall 

riser cord.

921-Device in PCI 

Express slot failed to 

initialize.

There is an 

incompatibility/problem 

with this device and the 

system or PCI Express 

Link could not be 

retrained to an X1.

Try rebooting the system. If the error 

reoccurs, the device may not work with 

this system.

✎

This error message applies to the PCI Express Graphics slot using Intel 9X1 Express chipsets. This 

slot supports x1 and x16 (PCI Express Link Width cards) only. If a x4 or x8 card is used, system 

BIOS will attempt to retrain to a x1. If this fails, the 921 error message will be displayed.

1720-SMART Hard 

Drive Detect Imminent 

Failure

Hard drive is about to 

fail. (Some hard drives 

have a firmware patch 

that will fix an erroneous 

error message.)

Determine if hard drive is giving correct 

error message. Run the Drive Protection 

System test if applicable.
Apply firmware patch if applicable. (see 

www.hp.com/support)
Back up contents and replace hard 

drive.

1785-MultiBay 

incorrectly installed 

 

(for MultiBay option on

 

non-USDT systems)
Multibay option ribbon 

cables not seated or 

improperly attached.
or
MultiBay device not 

properly seated.
or
MultiBay diskette present.

Ensure the MultiBay option is attached 

as device 0 on the IDE cable.
Ensure no other device is attached to the 

same IDE cable.
Ensure both ends of the IDE and 

MultiBay ribbon cables are properly 

seated.
Ensure the MultiBay device is fully 

inserted.
Ensure a MultiBay diskette is not present 

(MultiBay diskette drives are not 

supported by the MultiBay option).

POST Error Messages 

Screen Message

Probable Cause

Recommended Action

Summary of Contents for Compaq dx6100 MT



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands