manualshive.com logo in svg

HP Compaq dx2700 Microtower and Small Form Factor, Service & Reference Manual, Page: 80 / 107

Share
Download
HP Compaq dx2700 Microtower and Small Form Factor Service & Reference Manual Download Page 80

C–4

431672-001

Service Reference Guide

POST Error Messages

CMOS Checksum Bad

CMOS contents failed the 

Checksum check.

Restart the computer, use the F10 Key to 

access Computer Setup. Select 

Load 

Default Settings

 > 

Save and Exit

.

Keyboard Error

Keyboard not present or 

system not responding 

when keyboard controller 

is initialized.

Reconnect keyboard with computer 

turned off.
Check connector for bent or missing 

pins.
Ensure that none of the keys are 

depressed.
Replace keyboard.
Replace system board.

Keyboard/Interface 

Error

Keyboard controller 

failure.

Reconnect keyboard with computer 

turned off.
Check connector for bent or missing 

pins.
Ensure that none of the keys are 

depressed.
Replace keyboard.
Replace system board.

POST Error Messages 

Screen Message

Probable Cause

Recommended Action

Summary of Contents for Compaq dx2700 Microtower and Small Form Factor












































































































Reviews:

No comments