HP Compaq dx2700 Microtower and Small Form Factor Service & Reference Manual Download Page 14

Page: 14 / 107

2–6

431672-001

Service Reference Guide

Setup Utilities and Diagnostics Features

Advanced

BIOS Features

(continued)

Hard Disk Boot Priority

Allows you to specify the order of attached

hard drive devices (such as USB HDD

storage, USB2 Drive Key, or USB flash

media). The first drive in the order has

priority in the boot sequence and is

recognized as drive C (if any devices are

attached).

First Boot Device
Second Boot Device
Third Boot Device
Fourth Boot Device

Allows you to specify which devices will boot

first, second, and third, or to disable any of

the three:

• Removable
• Hard Disk
• CD-ROM
• Network
• Disabled

✎

MS-DOS drive lettering assignments

may not apply after a non-MS-DOS

operating system has started.

Boot Other Device

Disables/enables boot other device.

Load Boot Menu Selectable

Disables/enables boot menu selectable

APIC Mode

Disables/enables the APIC mode.

System Keyboard

Allows you to set system keyboard to absent

or present.

Boot Up NumLock Status

Allows you to set the default NumLock status
to off or on.

Security Option

Allows you to set the security option to Setup

or System so that the password is required

every time the system boots or only when

entering Computer Setup.

Computer Setup

(Continued)

Heading

Option

Description

✎

Support for specific Computer Setup options may vary depending on the hardware

configuration.

Summary of Contents for Compaq dx2700 Microtower and Small Form Factor












































































































Search results

Summary of Contents for Compaq dx2700 Microtower and Small Form Factor

Reviews:

Related manuals for Compaq dx2700 Microtower and Small Form Factor

Brands by name

Popular brands

HP Compaq dx2700 Microtower and Small Form Factor, Service & Reference Manual

Search results

Summary of Contents for Compaq dx2700 Microtower and Small Form Factor

Reviews:

Related manuals for Compaq dx2700 Microtower and Small Form Factor

Brands by name

Popular brands