HP Compaq dx2700 Microtower and Small Form Factor Service & Reference Manual Download Page 20 | Manualshive

Page: 20 / 107

background image

Service Reference Guide

431672-001

3–1

3

Desktop Management

✎

Support for specific features described in this guide may vary by model or software version.

3.1 Initial Configuration and Deployment

HP computers come with a preinstalled system software image. After a brief software
“unbundling” process, the computer is ready to be used.

A customized software image may be deployed by:

■

Installing additional software applications after unbundling the preinstalled software image.

The best deployment method depends on your information technology environment and
processes. The PC Deployment section of the Solutions and Services Web site

http://h18000.www1.hp.com/solutions/pcsolutions

provides information to help you select the

best deployment method.

The

Restore Plus!

CD, ROM-based setup, and ACPI hardware provide further assistance with

recovery of system software, configuration management and troubleshooting, and power
management.

3.2 ROM Flash

The computer’s BIOS is stored in a programmable flash ROM (read only memory). By
establishing a supervisor password in the Computer Setup (F10) utility, you can protect the ROM
from being unintentionally updated or overwritten. This is important to ensure the operating
integrity of the computer. Should you need or want to upgrade the BIOS, you may download the
latest BIOS images from the HP driver and support page: http://www.hp.com/support.

Ä

CAUTION:

For maximum ROM protection, be sure to establish a supervisor password. The supervisor

password prevents unauthorized ROM upgrades.

3.2.1 FailSafe Boot Block ROM

The FailSafe Boot Block ROM allows for system recovery in the unlikely event of a ROM flash
failure, for example, if a power failure were to occur during a ROM upgrade. The Boot Block is a
flash-protected section of the ROM that checks for a valid system ROM flash when power to the
system is turned on.

■

If the system ROM is valid, the system starts normally.

■

If the system ROM fails the validation check, the FailSafe Boot Block ROM provides
enough support to start the system from a bootable removable media that automatically
invokes system BIOS upgrade utilities.

To recover the system after it enters Boot Block recovery mode, complete the following steps:

«
...
18
19
20
21
22
...
»

Summary of Contents for Compaq dx2700 Microtower and Small Form Factor












































































































Reviews:

No comments

Related manuals for Compaq dx2700 Microtower and Small Form Factor

Brand: Sinclair Pages: 65

Brand: Aaeon Pages: 45

Brand: Cartft Pages: 10

Brand: AOpen Pages: 22

miniPC Duo MP965-DR

Brand: AOpen Pages: 56

WINSTON WORKSTATION

Brand: Innovative Pages: 11

Brand: SQlab Pages: 2

Brand: Janz Tec Pages: 20

Brand: Kano Pages: 54

Brand: FabiaTech Pages: 3

Brand: A.K.Microsystems Pages: 47

Brand: Faytech Pages: 2

Brand: QOCA spt Pages: 26

QutePC-5000 Series

Brand: Quanmax Pages: 38

Brand: Lanner Pages: 23

Brand: MAINGEAR Pages: 12

Brand: iDOT Pages: 6

Brand: Gateway Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands