background image

6-2

www.hp.com

Technical Reference Guide

Integrated Graphics Subsystem

6.2 Functional Description

The Intel Q35 GMCH component includes an Intel Integrated Graphics Media Accelerator 3100 
controller (Figure 6-1). This integrated graphics controller (IGC) operates internally of the PCIe 
x16 bus and can directly drive an external, analog multi-scan monitor at resolutions up to and 
including 2048 x 1536 pixels. The IGC includes a memory management feature that allocates 
portions of system memory for use as the frame buffer and for storing textures and 3D effects. 

The IGC provides two SDVO channels that are multiplexed through the PCIe graphics interface. 
These SDVO ports may be used by an Advanced Digital Display (ADD2) card installed in the 
PCI-E x16 graphics slot in driving two digital displays with a 200-megapixel clock. 

Figure 6-1. Q35 IGC, Block diagram

The IGC provides the following features:

Rapid pixel and texel rendering using four pipelines that allow 2D and 3D operations to 
overlap, speeding up visual effects, reducing the amount of memory for texture storage

Zone rendering for optimizing 3D drawing, eliminating the need for local graphics memory 
by reducing the bandwidth

Dynamic video memory allocation, where the amount of memory required by the application 
is acquired (or released) by the controller

Intelligent memory management allowing tiled memory addressing, deep display buffering, 
and dynamic data management

Provides two serial digital video out (SDVO) channels for use by an appropriate ADD2 
accessory card (SFF and CMT form factors only)

Drives a DVI monitor directly (USDT form factor only)

RGB

Integrated

Q35 GMCH

GMA 3100

Controller

Monitor

(System

DDR2

PCIe I/F

PCIe x16 

SDRAM

Controller

SDRAM

Memory)

Graphics slot [2]

NOTE:

PCIe

& SDVO Data

[2] SFF and CMT form factors only.

DVI-D

Monitor [1]

Analog

Digital

[1] USDT form factor only.

Summary of Contents for Compaq dc7800 MT







































































































Reviews: