HP C-Series Compatibility Manual Download Page 17 | Manualshive

Page: 17 / 24

background image

NOTE:

Cisco NPV mode can be supported with Brocade fabric configured in interopmode or Native
mode. If the MDS9124e NPV is connected to an external fabric comprising of only Brocade
switches, use Brocade Native mode only. If the MDS 9124e NPV is connected to an external fabric
with a mix of Brocade and Cisco switches, then Brocade (and Cisco) switches must be set to
interopmode 1.

•

Brocade AG mode is supported with FOS-OS 5.2.1b or later.

NOTE:

Brocade AG mode can be supported with Cisco fabric configured in interopmode or Native mode.
If the AG is connected to an external fabric comprising of only Cisco switches, use Cisco Native
mode only. If the AG is connected to an external fabric with a mix of Cisco and Brocade switches,
then Brocade (and Cisco) switches must be set to interopmode 1.
Brocade AG interoperability with Cisco is supported with Emulex HBAs only (no QLogic HBA
support).

•

Continuous Access EVA and Continuous Access XP storage systems are supported in a C-series
and B-series interoperable heterogeneous switch fabric configurations. See

Table 5

for supported

EVA and XP firmware versions.

B-series/

C-series

C-

series

Director

C-

series

Director

B-series/

C-series

B-series/

C-series

B-series/

C-series

B-series/

C-series

B-series/

C-series

B-series/

C-series

B-series/

C-series

B-series/

C-series

Recommended IOP configuration diagram

hosts

targets

hosts

targets

hosts

hosts

hosts

targets

targets

targets

hosts

hosts

targets

targets

targets

targets

targets

targets

hosts

hosts

hosts

hosts

Figure 1 Recommended IOP configuration diagram

Fabric interoperability: Merging fabrics based on C-series and B-series Fibre Channel switches applic-

ation notes

17

«
...
15
16
17
18
19
...
»

Summary of Contents for C-Series

























Reviews:

No comments

Related manuals for C-Series

GuardSwitch 300 Series

Brand: GE Pages: 4

Brand: FELA Pages: 13

Brand: IDEC Pages: 8

Brand: IDEM SAFETY SWITCHES Pages: 2

Brand: UNICOM Pages: 1

Brand: Cabletron Systems Pages: 120

Brand: GarrettCom Pages: 63

Brand: Kramer Pages: 2

RMQ-Titan M22-LED Series

Brand: Eaton Pages: 4

Brand: Microsens Pages: 8

EG2-1600 Series

Brand: Leonton Pages: 19

Brand: H3C Pages: 27

Brand: Optone Pages: 10

Brand: Emos Pages: 44

8 Port 10/100 Ethernet Switch

Brand: OnQ Technologies Pages: 14

Brand: Wantec Pages: 4

Brand: Unipoe Pages: 6

Brand: KTI Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands