HP Blade Blade Troubleshooting Manual Download Page 69

Page: 69 / 84

Troubleshooting Guide

www.hp.com

A–11

POST Error Messages

Network Server
Mode Active and
No Keyboard
Attached

Keyboard failure while
Network Server Mode
enabled.

1. Reconnect keyboard with computer

turned off.

2. Check connector for bent or missing

pins.

3. Ensure that none of the keys are

depressed.

4. Replace keyboard.

Parity Check 2

Parity RAM failure.

Run Computer Setup and Diagnostic
utilities.

System will not boot
without fan

CPU fan not installed or
disconnected in VSFF
chassis.

1. Open hood, press the Power button,

and see if the processor fan spins. If
the processor fan is not spinning,
make sure the fan's cable is plugged
onto the system board header. Ensure
the heatsink is properly seated and
installed.

2. If the fan is plugged in and the

heatsink is properly seated but the fan
does not spin, then replace the
heatsink-fan assembly.

Numeric Codes and Text Messages

(Continued)

Code/Message

Probable Cause

Recommended Action

Summary of Contents for Blade Blade





















































































Search results

Summary of Contents for Blade Blade

Reviews:

Related manuals for Blade Blade

Brands by name

Popular brands

HP Blade Blade, Troubleshooting Manual

Search results

Summary of Contents for Blade Blade

Reviews:

Related manuals for Blade Blade

Brands by name

Popular brands