Hardware specifications
Switch Chassis
Size (WxDxH)
442.5 x 473 x 43.95 mm (17.42x 18.62 x 1.73
inches)
Weight
8.95 kg (19.73 lb), with two installed PSUs
Temperature
Operating: 0°C to 40°C (32°F to 104°F)
Storage: -40°C to 70°C (-40°F to 158°F)
Humidity
Operating: 5% to 95% (non-condensing)
Operating
Altitude
Up to 3000 m (10,000 ft)
Acoustics
Noise Emission LpA=61.1 dB at virtual
workspace according to DIN 45635 T.19
Power
Consumption
282 Watts maximum
AC PSU
Power AC Input
Rating
100–240 VAC, 50-60 Hz, 400 Watts, hot
pluggable
System AC
Input Rating
100–240 VAC, 50-60 Hz, 6–3 A
Power DC
Output Rating
5 VDC @ 3 A
12 VDC @ 33 A
Regulatory Compliances
Emissions
EN 55022:2010, Class A
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013
FCC Class A
VCCI Class A
CE Mark
Immunity
EN 55024:2010
IEC 61000-4-2/3/4/5/6/8/11
Safety
UL 60950-1/CSA C22 2 No. 60950-1
EN/IEC 60950-1
EN60850-1/IEC 60825-1
Installation precautions
Warnings
•
The rack or cabinet should be adequately secured to
prevent it from becoming unstable, tilting, or falling.
•
Devices installed in a rack or cabinet should be mounted
as low as possible, with the heaviest devices at the bottom
and progressively lighter devices above.
Cautions
•
Ensure the power source circuits are properly grounded,
then use the power cord supplied with the switch to
connect to the AC power source.
•
If your installation requires a different power cord than the
one supplied with the switch and/or power supply, be sure
the cord is adequately sized for the switch’s current
requirements. In addition, be sure to use a power cord
displaying the mark of the safety agency that defines the
regulations for power cords in your country/region. The
mark is your assurance that the power cord can be used
safely with the switch and power supply.
•
When installing the switch, the AC outlet should be near
the switch and should be easily accessible in case the
switch must be powered off.
•
Ensure the switch does not overload the power circuits,
wiring, and over-current protection. To determine the
possibility of overloading the supply circuits, add together
the ampere ratings of all devices installed on the same
circuit as the switch and compare the total with the rating
limit for the circuit. The maximum ampere ratings are
usually printed on the devices near the AC power
connectors.
•
Do not install the switch in an environment where the
operating ambient temperature exceeds its specification.
•
Ensure the airflow around the switch is not restricted.
Leave at least 7.6 cm (3 inches) for cooling.
For additional safety and regulatory information, and switch
recycling information, refer to the safety and regulatory
documentation on the Hewlett Packard Enterprise website at
www.hpe.com/support/Safety-Compliance-EnterpriseProducts
Power cords
Argentina
Australia/New Zealand
Brazil
Chile
China
Continental Europe
Denmark
India
Israel
Japan
Malaysia
Switzerland
South Africa
South Korea
Taiwan
Thailand
United Kingdom/Hong Kong/Singapore
United States/Canada/Mexico
8121-0729
8121-0837
8121-1071
8121-0735
8121-0943
8121-0731
8121-0733
8121-0564
8121-1004
8121-1143
8121-0739
8121-0738
8121-0737
8121-0731
8121-0964
8121-0734
8121-0739
8121-1141
WARNING
FOR INDOOR USE ONLY. The switch, AC power cord,
and all connected cables are not designed for outdoor
use.
