HP AdvanceStack J2610B Installation And Reference Manual Download Page 23 | Manualshive

Page: 23 / 67

background image

The following illustration shows a hub with an HP ThinLAN Transceiver
Module connected to a thinLAN backbone.

Connecting the Hub-8U to a Fiber-Optic Backbone

With an HP Fiber-Optic Transceiver Module for 10Base-FL networks, you
can connect your hub to a fiber-optic backbone. The following illustration
shows a hub with an HP Fiber-Optic Transceiver Module connected to a fiber-
optic backbone:

For more information about cabling configuration, see the documentation
accompanying the optional transceiver modules.

See the

Designing HP AdvanceStack Networks

guide for information on

valid network topologies.

ThinLAN
backbone

HP J2606A Fiber-Optic
Transceiver Module installed
in the AUI/Xcvr Slot

fiber-optic
cable

Inst

alling the Hub

Installing the Hub

1-13

«
...
21
22
23
24
25
...
»

Summary of Contents for AdvanceStack J2610B




































































Reviews:

No comments

Related manuals for AdvanceStack J2610B

Brand: iGenix Pages: 6

SMART ECG 1000 A

Brand: Airtecnics Pages: 22

Brand: Stahls Hotronix Pages: 15

Brand: N'oveen Pages: 21

Brand: Stahl Pages: 45

Ethernet DI-789

Brand: Dataq Pages: 22

Brand: LINK-MI Pages: 3

Brand: Sonnenkonig Pages: 48

Brand: Uberhaus Pages: 18

1500W STOVE HEATER

Brand: DELLA Pages: 14

Perfectclime RELAX DARK IRC IP55 Series

Brand: Burda Pages: 32

Brand: AirNmore Pages: 8

Brand: SPT Pages: 8

Brand: C. Crane Pages: 4

ESSENSSE NEO VCES2-B-AC Series

Brand: 2VV Pages: 20

Brand: Gabarron Pages: 4

Brand: EINHELL Pages: 56

Brand: Singer Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands