HP AdvanceStack J2610B Installation And Reference Manual Download Page 12 | Manualshive

Page: 12 / 67

background image

This chapter describes how to install the HP AdvanceStack Hub-8U, verify
its operation, and connect it to a network, other hubs, computers, and/or
other devices.

Installation Summary

The basic hardware installation procedure for the HP AdvanceStack Hub-8U
is as follows:
1. Install the optional HP AdvanceStack 8U/16U SNMP Module and/or

one of the optional HP Transceiver Modules.

2. Verify the hub’s operation.
3. Mount the hub on a wall or under a tabletop.
4. Connect the hub to a network or other hubs, and connect

computer(s) and/or other device(s) to the hub’s ports.

5.

(Optional)

Connect the hub to the AdvanceStack 8U/16U SNMP

management console.

Included Parts

Each HP AdvanceStack Hub-8U has the following components shipped with
it:

HP AdvanceStack Hub-8U Installation and Reference Guide

—this

manual

(J2610-90101)

An ac power cord, one of the following:

Australia/New Zealand
Denmark
Europe
Japan
Switzerland
United Kingdom/Hong Kong
U.S./Canada

(8120-1369)
(8120-2956)
(8120-1689)
(8120-4753)
(8120-2104)
(8120-1351)
(8120-1378)

A power supply, part number 0950-3058

Installin

g

the

Hu

b

Installing the Hub

1-2

«
...
10
11
12
13
14
...
»

Summary of Contents for AdvanceStack J2610B




































































Reviews:

No comments

Related manuals for AdvanceStack J2610B

Brand: Jata calor Pages: 16

Brand: Gabarron Pages: 8

Brand: KEKAI Pages: 12

Brand: JBL Pages: 12

Brand: Superior Radiant Pages: 12

Brand: Modine Manufacturing Pages: 32

Brand: Scarlett Pages: 14

Brand: TCP Smart Pages: 16

Brand: Envirovent Pages: 28

Brand: Vam Teplo Pages: 16

Brand: Outwell Pages: 32

Brand: Strend Pro Pages: 50

Brand: Fenix Pages: 8

Brand: Caltech Pages: 60

Brand: Comfort Zone Pages: 9

Brand: Kogan Pages: 3

Brand: Waves Pages: 17

The Com-Pak Plus

Brand: Cadet Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands