HP 9000 Series Service Manual Download Page 419

Page: 419 / 472

Appendix B

B-15

Support Information

---BootID Help -----------------------------------------------

BootID is used to display or set id for processor
installed in the system.

BootID

Display the boot id for all processors

BootID BBprocessorEB

Display the boot id for all the processor

BootID BBprocessorEBBBbootidEB

Sets the boot id for the processor.

Short commands for BootID: bid

---------

---Warnings Help ----------------------------------------------

WArnings is used to display the selftest warning messages.

Short commands for WArnings: wa

-----------

---Chiprevisions Help ----------------------------------------

ChipRevisions displays the revisions of the major VLSI chips
in the system.

It also displays the current PDC internal version number.

Short commands for ChipRevisions: cr

------

---Cache Help------------------------------------------------------

CAche displays information about the cache sizes on the
processors present in the system.

Short commands for CAche: ca

--------

---Coprocessor Help ----------------------------------------------

COprocessor displays information about the floating point
coprocessors present in the system.

Short commands for COProcessor: cop

-------

Summary of Contents for 9000 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for 9000 Series

Reviews:

Related manuals for 9000 Series

Brands by name

Popular brands

HP 9000 Series, Service Manual

Search results

Summary of Contents for 9000 Series

Reviews:

Related manuals for 9000 Series

Brands by name

Popular brands