HP 9000 Series Service Manual Download Page 138

Page: 138 / 472

4-22

Chapter 4

D200/D210/D310 Front Panel LCD Codes

Table 4-14 Boot Device Initialization and IPL codes for all other paths.

Table 4-15 TOC codes.

Ostat

Code Name

Meaning

INIT

C700

GET_MANUF_DFLTS

Retrieving Manufacturing defaults.

INIT

C740

INIT_MANUF_DFLTS

INIT

C740

INIT_OTHR_PATH

Initializing manufacturing defaults.

TEST

C750

TEST_OTHR_PATH

Initializing a non-primary boot path.

INIT

C780

LOAD_IPL_OTHR_PATH

Loading IPL from a non-primary boot
device.

WARN

C7F0

OTHR_IPL_FAULT

Error occurred reading IPL from boot
media.

WARN

C7F1

BAD_IPL_ADDR_OTHR

LIF file address is not 2K byte aligned or it
is zero.

WARN

C7F2

BAD_LIF_MAGIC_OTHR

LIF file not present on media.

WARN

C7F3

BAD_IPL_SIZE_OTHR

LIF file is not a multiple of 2K bytes, is zero
or it is greater than 256K bytes.

WARN

C7F4

BAD_IPL_ENTRY_OTHR

LIF file entry is not word aligned or is
greater than or equal to the size.

WARN

C7F8

BAD_IPL_CHECKSUM_OTH
R

The arithmetic sum of the words in IPL 0.

INIT

C7FF

LAUNCH_IPL_OTHR

Branching to IPL form a non-primary boot
device.

Ostat

Code Name

Meaning

INIT

CB00

TOC_INITIATED

TOC handler entered

TEST

CB0B

BR_TO_OS_TOC

Branching to OS_TOC

Summary of Contents for 9000 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for 9000 Series

Reviews:

Related manuals for 9000 Series

Brands by name

Popular brands

HP 9000 Series, Service Manual

Search results

Summary of Contents for 9000 Series

Reviews:

Related manuals for 9000 Series

Brands by name

Popular brands