background image

 

 

 

2

 

Product Introduction 

 

 

A.

 

  Purpose 

        HOUGHTON  BELAIRE  is  designed  to  provide  a  comfortable  environment  inside  a  recreational  vehicle  or 

caravan. 

 

     

  B.    How to provide an efficient operation

 

Many  factors  will  affect  the  total  heat  load  within  the  caravan  and  many  factors  can  also  affect  the  working 

efficiency  of  the  air-conditioner.  Before  purchasing  HOUGHTON  BELAIRE,  the  user  shall  consult  with  the  caravan 

manufacturer  to  understand  the  total  heat  load  of  the  caravan  and  to  choose  the  correct  air-conditioner  for  the 

application. 

The  following  measures  are  very  useful  to  reduce  the  heat  load  within  a  caravan  or  RV  and  improve  the 

performance of the air-conditioner.   

 

Close all the doors, skylights and windows, draw the curtains and open the sunshade.   

 

Adjust the ca

ravan’s position to make sure the sunshade is on the southern side in the northern hemisphere or on 

the northern side in the southern hemisphere. This will reduce the exposure to direct sunshine.   

 

Turn off the unnecessary electrical appliances within the caravan to reduce the heat-load. 

 

Please cook outside of the caravan. 

 

Park the caravan at a shade place.   

 

In case of exceptional high temperature, turn on the air-conditioner in advance during the morning. 

 

Adjust the set temperature of the remote control to prevent from frequent start or stop of the unit. 

 

 

    C.    Condensation 

 

        For the areas where the air humidity is comparatively low, when the warm moist air within the caravan meets with 

the cold wind from the outlet, condensate water may be caused, which 

is also called as “sweating”. In this case, make 

sure the following measures are taken: 

 

Close all the doors, skylights, windows and draw the curtains to reduce the warm moist air incoming. 

 

In  the  operation  of  the  air-conditioner,  a  large  number  of  condensate  water  will  be  produced  on  the  roof  as  the 

warm moist air is exhausted by the operation of the air-conditioner. The size of the condensate water is decided by 

the air humidity. In this case, do not adjust the wind FAN to low or auto mode but adjust it to high FAN mode to 

increase the circulation of the air and reduce the condensation degree. 

 

      Please be noted that losses caused by the condensate water are not within warranty scope. 

 

     

D.    Choosing and using of generator 

 

HOUGHTON  BELAIRE  requires  an  AC  power  source.and  may  require  for  generator  driving  in  some  remote 

areas. Requirements for generator include: efficient power source, stable currency, output waveform: sine wave, 

that shall meet the driving requirements of the compressor. The user shall consult with the generator supply and 

fully refer to their suggestions. 

 

      Please be noted that losses caused to the product by the using of the generator are not within warranty scope. 

 

 

 

Summary of Contents for BELAIRE HB3200


























Reviews: