15
Operations
3.
Press pump
STOP
switch.
4.
Turn water supply
OFF.
5.
Squeeze trigger of trigger gun to relieve system
pressure.
Cleaning Techniques
Pre-rinse cleaning surface with fresh water. Place
detergent suction tube directly into cleaning solution and
apply to surface at low pressure (for best results, limit
your work area to sections approximately 6 feet square
and always apply detergent from bottom to top). Allow
detergent to remain on surface 1-3 minutes. Do not allow
detergent to dry on surface. If surface appears to be
drying, simply wet down surface with fresh water. If
needed, use brush to remove stubborn dirt. Rinse at high
pressure from top to bottom in an even sweeping motion
keeping the spray nozzle approximately 1 foot from
cleaning surface. Use overlapping strokes as you clean
and rinse any surface. For best surface cleaning action
spray at a slight angle.
Recommendations:
•
Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
distance for maximum cleaning results.
•
If painted surfaces are peeling or chipping, use
extreme caution as pressure washer may
remove the loose paint from the surface.
•
Keep the spray nozzle a safe distance from the
surface you plan to clean. High pressure wash a
small area, then check the surface for damage. If
no damage is found, continue to pressure
washing.
CAUTION - Never use:
•
Bleach, chlorine products and other corrosive
chemicals
•
Liquids containing solvents (i.e., paint thinner,
gasoline, oils)
•
Tri-sodium phosphate products
•
Ammonia products or acid-based products
ATTENTION: Ne jamais utiliser :
•
Eau de Javel, produits à base de chlore et autres
produits chimiques corrosifs
•
Liquides contenant des solvants (c.-à-d. diluant à
peinture, essence, huiles, etc.)
•
Produits à base de tripolyphosphate de sodium
•
Ammoniac ou produits à base d'acide
These chemicals will harm the machine and will damage
the surface being cleaned.
Rinsing
It will take a few seconds for the detergent to clear. Apply
safety latch to spray gun. Select and install desired high
pressure nozzle.
NOTE:
You can also stop detergent
from flowing by removing detergent siphon tube from
bottle.
Storage
DANGER: DO NOT store flammable liquids (gaso-
line, diesel fuel, solvents, etc.) near pressure washer,
or in non-ventilated areas.
DANGER: Ne pas entreposer de liquides
inflammables (essence, mazout, pétrole, solvants,
etc.) à proximité de la laveuse à pression ou dans
des endroits non ventilés.
Protect from freezing by storing in a heated area, or by
flushing the system with antifreeze (use an automotive
engine antifreeze or windshield washer solvent to anti-
freeze). To flush the system fill the float tank with anti-
freeze and remove pressure nozzle from wand. Start the
machine and allow it to run until antifreeze flows from the
end of the wand. Place end of wand into float tank and
circulate the antifreeze through system for several
minutes. Squeeze and release the trigger of the trigger
gun several times to antifreeze the unloader system.
Also draw antifreeze through the detergent inlet line to
antifreeze the detergent system. For added protection
after antifreezing, disconnect the pressure hose from
machine and remove the coil drain plug. After coil has
drained, replace pressure hose and coil drain plug. If the
pressure washer is not to be used for an extended length
of time, it is recommended that the system be flushed
with antifreeze for rust protection.
Maintenance
WARNING: Unauthorized machine modification or
use of non-approved replacement parts may cause
personal injury and/or property damage and will void
the manufacturer warranty.
AVERTISSEMENT: Une modification non autorisée
de la machine ou l'utilisation de pièces de rechange
non approuvées peut causer des lésions corporelles
et/ou des dommages à la propriété, et annulera la
garantie du fabricant.
MANUAL, OPERATOR, HOTSY, STAT ELECTRIC, OIL 8.916-831.0 - D
