background image

5

Safety

Introduction & Safety Information

Thank you for purchasing this Pressure Washer.

We reserve the right to make changes at any time 
without incurring any obligation.

Owner/User Responsibility:

The owner and/or user must have an understanding of 
the manufacturer’s operating instructions and warnings 
before using this pressure washer. Warning information 
should be emphasized and understood. If the operator 
is not fluent in English, the manufacturer’s instructions 
and warnings shall be read to and discussed with the 
operator in the operator’s native language by the 
purchaser/owner, making sure that the operator 
comprehends its contents.

Owner and/or user must study and maintain for future 
reference the manufacturers’ instructions.

The operator must know how to stop the machine 
quickly and understand the operation of all controls. 
Never permit anyone to operate the engine without 
proper instructions.

SAVE THESE INSTRUCTIONS

This manual should be considered a permanent 
part of the machine and should remain with it if 
machine is resold.
When ordering parts, please specify model and
serial number. Use only identical replacement 
parts.This machine is to be used only by trained 
operators

MANUAL, OPERATOR, HOTSY, STAT ELEC NG-LP    9.808-037.0-A 

Summary of Contents for 1800 Series































Reviews: