manualshive.com logo in svg

Hotsy 1.110-043.0, Operator'S Manual

Share
Download
Hotsy 1.110-043.0 Operator'S Manual Download Page 19

19

Maintenance

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

ENGINE WILL 

NOT RUN

No fuel

Replenish supply.

Low battery

Charge battery.

Poor battery cable connection

Clean battery terminals and check cables.

Refer to provided engine manual for additional troubleshooting.

NO WATER FROM 

PRESSURE 

NOZZLE

Pressure nozzle clogged

Clean pressure nozzle.

Inlet water screen clogged

Clean.

Pumping sucking air

Fill the detergent container. Check for loose hose 
clamps or fittings.

POOR OR NO 

DETERGENT 

FLOW

Low detergent level

Replenish supply.

Detergent screen clogged

Clean.

Detergent metering valve not opening Check that handle or knob is not slipping on shaft.

Pressure nozzle clogged

Clean.

LOW PRESSURE 

FROM SPRAY 

NOZZLE.

Inlet clogged

Clean

Spray nozzle worn or incorrect size

Replace.

Inadequate water supply

Increase water supply.

Pump sucking air

Fill the detergent container. Check for loose hose 
clamps or fittings.

UNLOADER 

VALVE CYCLES 

WHEN TRIGGER 

GUN IS OPEN 

OR CLOSED

Air in system

Open and close trigger gun several times.

Defective unloader valve

Repair or replace.

Water leak between unloader valve 
and trigger gun.

Check fittings, hose and trigger gun for leaks. Repair 
or replace.

BURNER 

WILL NOT IGNITE 

WHEN TRIGGER 

GUN IS OPEN

No fuel

Replenish supply.

Adjustable thermostat set too 
low Defective pressure switch

Electrodes are dirty or out of adjust-
ment  No AC generator output

Raise temperature setting.  Repair or replace.
Refer to 

OIl Burner Manua

l  provided with machine.

Check AC generator.

BURNER 

SMOKES OR

HAS 

OBNOXIOUS 

ODOR

Air bands need to be adjusted

Improper fuel

Readjust. Refer to 

Oil Burner Section

 under 

Instal-

lation

.

Use kerosene, #1 Grade Home Heating Oil, #1 or  #2 
Diesel Fuel.

DO NOT USE GASOLINE.

Hotsy 1200 Operator’s Manual  8.914-366.0 - AC

Summary of Contents for 1.110-043.0







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands