manualshive.com logo in svg

Hotsy 1.110-043.0, Operator'S Manual

Share
Download
Hotsy 1.110-043.0 Operator'S Manual Download Page 17

17

Operations

Shutdown Instructions 

1.

If detergents were used, draw clear water through 
the system to purge detergent.

2.

If burner was used, turn OFF burner switch, and 
allow pump to run cold water through coil.

3.

Move throttle control to idle position.

4.

Turn key on engine counterclockwise (CCW) to 
OFF position.

5.

Turn OFF fuel shut-off valve.

6.

Turn OFF water supply.

7.

Squeeze trigger gun open to relieve system 
pressure.

Storage 

DANGER: Do not store flammable liquids (gasoline, 
solvents, etc.) near pressure washer, or in non-
ventilated areas.

Protect from freezing by storing in a heated area, or by 
flushing the system with antifreeze. To flush the 
system, fill the float tank with antifreeze and remove 
spray nozzle from wand. Start the machine and allow it 
to run until antifreeze flows from the end of the wand. 
Place end of wand into float tank and circulate the anti-
freeze through system for several minutes. Open and 
close the trigger gun several times to circulate anti-
freeze through the unloader valve. Place detergent line 
into the float tank. Open the detergent metering valve to 
draw antifreeze into the detergent system.

If the pressure washer is not to be used for a consider-
able length of time, it is recommended to flush the 
system with antifreeze for rust protection.

Hotsy 1200 Operator’s Manual  8.914-366.0 - AC

Summary of Contents for 1.110-043.0







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands