Page 22
TO ADJUST BALANCE
From the SETUP screen:
1. Press the
(+)
button to display one of four audio sources, IPOD,TV, AUX, BLUE.
2. Press the MODE (
) button to display TRE.
3. Press the MODE (
) button to display BAS.
4. Press the MODE (
) button to display BAL -5 to +5.
5. Press
(+)
button to raise the Balance # or press
(-)
button to lower the Balance #.
TO ADJUST SUBWOOFER
From the SETUP screen:
1. Press the
(+)
button to display one of four audio sources, IPOD,TV, AUX, BLUE.
2. Press the MODE (
) button to display TRE.
3. Press the MODE (
) button to display BAS.
4. Press the MODE (
) button to display BAL.
5. Press the MODE (
) button to display SUB 0 to 11.
6. Press
(+)
button to raise the subwoofer # or press
(-)
button to lower the subwoofer #.
TO CHANGE AMPLIFIER CHANNEL
(TO MATCH WIRELESS DOCK TRANSMITTER INSIDE
HOUSE IF INSTALLED)
From the SETUP screen:
1. Press the
(+)
button to display one of four audio sources, IPOD,TV, AUX, BLUE.
2. Press the MODE (
) button to display TRE.
3. Press the MODE (
) button to display BAS.
4. Press the MODE (
) button to display BAL.
5. Press the MODE (
) button to display SUB.
6. Press the MODE (
) button to display CHAN 1-5.
7. Press
(+)
button to raise the channel # or press
(-)
button to lower the channel #.
NOTE:
Channel number must match Transmitter number inside house to work properly
SPA CONTROL PANEL- SX & TX MODELS ONLY
Your control panel consists of an LED display and convenient touch
pads that allow you to set the water temperature and adjust the skim/
filter cycle settings, lock spa temp, lock entire spa functions, as well as
control the hydrotherapy jets, and lights from spa-side.
LED DISPLAY
The LED display on your spa-side control panel continually shows the
spa’s actual water temperature. In certain situations, it will also display
other messages. See TROUBLESHOOTING section.
SET BUTTON
Use the set button to control clean cycle, filter cycle, locking and light
functions. To activate the desired mode, press the
SET
button. When
the “SET” icon flashes push the applicable button. The SET mode
ends after 3 seconds or when the“SET” icon stops flashing.
TEMPERATURE CONTROL
The set temperature range is from 80°F
(26°C) to 104°F (40°C). Temperatures
of any setting may rise slightly depending on the current use and condition of your spa, and on outside temperature.
Whenever power is disconnected and then reconnected to the spa, the water temperature setting will automatically
return to the last temperature entered into the program.
Page 22
Operating Instructions
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
Temp / Lock
Display
Light Icon
Filter Cycle Icon
Jets Button
Light Button
Temperature Down
Temperature Up
Set Button
Set Icon
Sleep
Icon
Temp
Ready
Icon
Filter Cycle
2 Icon
Filter Cycle 1
Icon
Jet Icon
SET
READY
F1
F2
READY
READY
READY
READY
READY
READY
READY
F1
SET
READY
F1
F2
SET
F1
F2
SET
READY
F1
F2
READY
