HotSpring FLR, Owner'S Manual

Page: 33 / 44

LIMELIGHT
™
WATER TREATMENT GUIDE
At hot tub
startup
or refill
Follow hot tub Start-Up and Refill Procedures.
NOTE: Use the FreshStart
®
10,000
pre-filter when filling the
spa to remove unwanted contaminants.
Prior to
each use
(Test before adding any
chemicals; do not add any
chemicals if proper, or higher
levels are found.)
Add one (1) tablespoon of monopersulfate (MPS)* per
250 gallons (950 liters)
LimelightPulse (Model PLS)
1-1/3 tablespoons
LimelightFlair (Model FLR) 1 tablespoons
LimelightGlow (Model GLW) 1 tablespoons
Add one half (1/2) teaspoon of sodium dichlor
per 250 gallons (950 liters)
LimelightPulse
™
(Model PLS) 2/3 teaspoon
LimelightFlair
™
(Model FLR) 1/2 teaspoon
LimelightGlow
™
(Model GLW) 1/2 teaspoon
Once a
week
Add three (3) tablespoons of monopersulfate
(MPS)* per 250 gallons (950 liters)
LimelightPulse (Model PLS)
4 tablespoons
LimelightFlair (Model FLR) 3 tablespoons
LimelightGlow (Model GLW) 3 tablespoons
Add one and one half (1.5) teaspoons of sodium
dichlor per 250 gallons (950 liters)
Limelight Pulse (Model PLS)
2 teaspoons
Limelight Flair (Model FLR) 1.5 teaspoons
Limelight Glow (Model GLW) 1.5 teaspoons
Every four
months
Drain and refill your hot tub.
Replace the FreshWater
Ag+
silver ion purifier
NOTE: Use the FreshStart
10,000
pre-filter when filling the
hot tub to remove unwanted contaminants.
Add one and one half (1.5) teaspoons of sodium dichlor
per 250 gallons (950 liters)
Limelight Pulse (Model PLS)
2 teaspoons
Limelight Flair (Model FLR) 1.5 teaspoons
Limelight Glow (Model GLW) 1.5 teaspoons
As needed,
if water is hazy,
cloudy, or has
an odor
OR
OR
*MPS is an oxidizer, not a sanitizer.
Page 30
Page 30
FRESHWATER
®
Ag+
SILVER ION PURIFIER REPLACEMENT
When replacing the silver ion purifier (every four months), it is highly recommended that the hot tub be drained and refilled at the same time. After
refilling the hot tub with water, balance the Total Alkalinity (TA), Calcium Hardness (CH) and pH to the recommended levels. Shock the hot tub by
adding sodium dichlor (See Sanitization Table for details).
1. Fold back the vinyl cover.
2. Carefully remove and set aside the filter compartment cover.
3. Remove any floating items within the filter compartment.
4. Locate the gray filter cap. Turn the filler cap counterclockwise until the cap can be removed from the filter standpipe.
5. Remove and clean filter cartridge.
NOTE:
When replacing the FreshWater
Ag+
silver ion purifier, it is an excellent time to clean and rotate the filter to extend its life. To rotate the
filter, simply replace the existing filter with another one. Then clean and store the old one until the next time the FreshWater
Ag+
silver ion
purifier needs replacement.
6. Remove the existing FreshWater
Ag+
silver ion purifier.
7. Install the new FreshWater
Ag+
silver ion purifier into the filter standpipe. Do not force the FreshWater
Ag+
silver ion purifier down into the filter
standpipe.
8. Reinstall the cleaned filter cartridge.
9. Replace and secure the gray filter cap.
10. Replace the filter compartment cover.
11. Fold the cover back into place.
WARNING:
Never use the hot tub with the filter cartridge or filter standpipe removed!
Water Quality and Maintenance