background image

Page 19

LIGHT - ON/OFF & INTENSITY CONTROLS

The light control uses four positions: High, Medium, Low, and Off. To turn on the hot tub light, press the LIGHT button. This will place all lights in

the hot tub in the High, or maximum intensity position. When the lights turn on, the light symbol will also illuminate on the control panel display.

Press the LIGHT button again to lower the intensity of the lights to the Medium position. Press the LIGHT button

again to lower the intensity even more, placing the lights intensity in the Low position. Press the LIGHT button one

more time to shut the lights off. When the light is deactivated, the light symbol will also turn off. 
If the lights are left on, they will automatically be turned off by the control system after 6 hours of continuous

operation. The light symbol on the panel will also turn off when the lights are deactivated.
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on the control panel (see following pages for

more information on SPA LOCK).

LIGHT - MULTI-COLOR MENU CONTROLS

Your hot tub lights can display a variety of different colors as well as run through a continuous sequence of colors (loop) at different speeds. To

activate  this function the following is required: 

On the control panel press the LIGHT button first (light will activate), then press the MODE 

or MODE  

▼ 

button to scroll to the LITE+ menu.

Once displayed, press the ON 

▲ 

button to enter the Lite menu. Press the MODE 

or MODE  

▼ 

button to scroll from COLOR - LOOP# - EXIT

screens. Press the ON 

▲ 

button or OFF 

▼ 

button in the COLOR screen as many times as desired to toggle through the different light colors. Press

the ON 

▲ 

button or OFF 

▼ 

button in the LOOP screen to select a continuous sequence of colors, the higher the loop number the faster the color

sequence will run. Press the ON 

▲ 

button in the EXIT screen to exit the LITE+ menu. 

NNO

OTTEE:: If the light is turned off while in the LOOP or COLOR mode, the same mode will exist when the light is reactivated.

INDICATOR LIGHTS

At a glance, the indicator lights are readily visible on the main control panel. The two indicator lights (POWER and READY) work independently

from the rest of the control panel display. That way, even if the control panel is off, you can simply glance at the “READY” indicator light to

determine whether or not your hot tub is within the range of your set temperature.

Power indicator: 

The POWER indicator is ‘on’ when the hot tub is properly supplied with power. It also provides a diagnostic function – a blinking

POWER indicator indicates that the heater high-limit has tripped, meaning that either the hot tub water is above its acceptable temperature range,

or a malfunction has occurred within the hot tub (such as low circulation due to a clogged filter). An ‘off’ POWER indicator means that there is a

problem with the hot tub control panel or the power supplied to the hot tub.

Ready indicator: 

The READY indicator will light when the hot tub water temperature is within 2-1/2°F of the set temperature, and will turn off when

the temperature is outside of that range. If you increase or decrease the temperature setting of the hot tub, the READY indicator will turn off until

the hot tub temperature reaches the acceptable range for the new set temperature. Additionally, a blinking READY indicator indicates that a

problem exists with the temperature sensor.

CONTROL PANEL MENU DISPLAY

The control panel consists of four main menus. These menus are; Set Temperature, System, Lite+ and Tools. Press the MODE 

or MODE  

button to scroll through the main menus. Once the desired menu is illustrated, press the ON 

▲ 

button to activate the menu.

TEMPERATURE CONTROL 

The set temperature range is from 80°F to 104°F 

(27°C  to 40°C)

.  (The temperature of any setting may rise

slightly depending on the current use and condition of your hot tub, and on outside temperature.)
The set temperature of the hot tub water will automatically be 102°F (

39°C)

the first time power is applied. This is

the setting programmed at the factory. After the hot tub has been set up and used, the last temperature value set

by the user will be stored in memory. If power is disconnected from the hot tub, it will automatically revert to the last set temperature when power

is reapplied.
To display the set temperature of the hot tub, press the ON 

▲ 

button. The set temperature will be displayed, unless the hot tub is locked (in which

case the lock icon is displayed). The set temperature display will automatically shut off after 30 seconds.
To increase the set temperature of the hot tub water, press ON 

▲ 

button. Each time the button is pressed, the set temperature display will

increment by one degree. If the button is held down, the set temperature display will increase by one degree every half-second. 
To decrease the set temperature of the hot tub water, press the OFF 

▼ 

button . Each time the button is pressed, the set temperature display will

decrement by one degree. If the button is held down, the set temperature display will decrease by one degree every half-second.
If the set temperature value will not change, check the TEMPERATURE LOCK and SPA LOCK features (see following pages for more information

on TEMPERATURE LOCK & SPA LOCK). When either of these features is applied, the temperature control is disabled. To activate the temperature

control buttons, remove all locking features applied.

Light Display

Set Temperature Display

Page 19

Control Panel Operation

Summary of Contents for FLR













































Reviews: