background image

12

GB

Start and Programmes

The Controls

•  

 PROGRAMMES knob

! Warning, 

if after pressing the start button, the programmes 

knob position is changed, the new position will 

NOT

 change 

the programme selected. To change a selected programme, 

press the Start/Pause button  , the light flashes Amber 

to indicate the programme is paused. Select the new 

programme and any options required, the light will then flash 

green. Press the Start/Pause button   again and the new 

programme will start.

• 

 

OPTION buttons / lights

These buttons are used to customise the selected 

programme to your requirements. Not all options are 

available for all programmes or a previously selected 

one. If an option is not available and you press the 

button, the buzzer will beep three times. If the option 

is available the option light next to the button lights to 

confirm the selection.

Progress ( 

 Drying, 

Cool Tumble, End) /

Delay (3hr 6hr 9hr) Lights

When the light next to the delay button is on, these lights 

flash to indicate the delay time selected. During other 

programmes they indicate the progress of the dryer, each 

one comes on as the corresponding phase starts.

Delay Timer

The start of some programmes 

(see Start and Programmes)

 

can be delayed for up to 9 hours in 3hr steps. Ensure the 

water bottle is emptied before setting a delayed start.

When a delayed start is in progress the light next to the delay 

button will be on and the selected delay period light will flash 

(after the start button has been pressed).To set a delayed 

start, press the Delay Timer button, and the light next to the 

button will come on together with the 3hr delay light. Pressing 

the button again will advance the delay setting to 6hr, the 3hr 

light goes out and the 6hr light is on. Each time you press 

the button the delay setting advances 3 hours, as indicated 

by the corresponding light. If the 9hr light is on, pressing 

the button again will cancel the delay. Holding in the On/Off 

button will also cancel.

Extra Care

This Anti-Ageing function for Cottons helps to maintain the 

brightness of your laundry for a long time, thanks to the 

correct drum rotation (reduced in the last part of the cycle) 

and the correct temperature.

Crease Care

The 

pre-care option

 is only available if a delayed start has 

been selected. It tumbles the clothes occasionally during 

the delayed period to help prevent creases developing. The 

post-care option

 occasionally tumbles the clothes after the 

end of the drying and cool tumble cycles to prevent creases 

developing, should you not be available to remove the load 

immediately the programme is complete.The End light is on 

during this phase. 

Note:

 The Start/Pause light flashes Amber 

during this phase. Selecting this option enables both the pre 

and post care functions if appropriate.

High Heat

Press this button and a high heat setting is selected and the 

light next to the button comes on. If the light alongside the 

button is on then pressing the button selects a low heat setting 

and the light goes out. Not all programmes allow you to change 

this setting.

Empty Water Light / Container

(If you have plumbed your dryer to a drain this light can be 

ignored, as there is no need to empty the water container). 

When this light is on (not flashing) it reminds you to empty the 

water container. If the water container fills during a programme, 

the heater turns off and the dryer does a period of Cool Tumble 

then the light flashes and the buzzer sounds. You must empty 

the water container and restart the dryer or the clothes will not 

dry. After re-starting the dryer, the light will take a few seconds 

to go out. To avoid this always empty the water container each 

time you use the dryer 

(see Maintenance).

• 

 

Door Opening

Opening the door (or pressing the Start/Pause button) during a 

programme will stop the dryer and have the following effects:

Note:

 The Start/Pause light flashes Amber during the Post Care 

phase of a programme.

• 

The Start/Pause light flashes Amber.

• 

During a delay phase the delay will continue to count 

down. The Start/Pause button 

must

 be pressed to resume 

the delay programme. One of the delay lights will flash to 

show the current delay setting.

• 

The Start/Pause button 

must

 be pressed to resume the 

programme. The progress lights will change to show the 

current status and the Start/Pause light will stop flashing 

and turn green.

• 

During the Post Creasecare phase of a drying programme, 

the programme will finish. Pressing the Start/Pause button 

will re-start a new programme at the beginning.

• 

Changing the programmes knob will select a new 

programme and the Start/Pause light will flash green. You 

can use this to select the 

 Refresh programme to cool 

the clothes, if you find them dry enough. Press the Start/

Pause button to begin a new programme.

Heat Pump Protection System

The heat pump system has a compressor protection

feature that operates if you open the door or there is a

power disruption or if you turn off the dryer. This system

will prevent the heat pump compressor from starting for 5

minutes after the door is closed and the programme is

started.

• 

Note

If you have a power cut, switch off the power or remove the 

plug. When power is restored, press and hold the ON/OFF 

button until the dryer reactivates, then press the Start/Pause 

button.

Summary of Contents for FTCL 87

















Reviews: