15
GB
The Controls
!
Warning,
after pressing the
START/PAUSE
button
,
the programme cannot be changed. To change a selected
programme, press the
START/PAUSE
button
the light
flashes Amber to indicate the programme is paused. Select
the new programme and any options required, the light will
then flash green. Press the
START/PAUSE
button
again
and the new programme will start.
•
Option buttons
These buttons serves to personalise the selected
programme according to personal requirements.
Not all options are available for all programmes.
Some options are incompatible with the ones
previously set. If the button of any unavailable option
is pressed, the buzzer will beep 3 times. If the option
is available, the option light will stay on.
Delay Timer (Time Delay)
The start of some programmes
(see The Display and
Programmes tables)
can be delayed for up to 24 hours.
Ensure the water container is emptied before setting a
delayed start.
Crease Care
The
pre-care option
is only available if a delayed start has
been selected. It tumbles the clothes occasionally during
the delayed period to help prevent creases developing. The
post-care option
occasionally tumbles the clothes after end
of the drying and cool tumble cycles to prevent creases
developing, should you not be available to remove the load
immediately the programme is complete
Note:
The
START/PAUSE
light flashes Amber during
this phas
e. Selecting this option enables both the pre and
post care functions i
f appropriate.
Note:
If you have selected the Sound option this option is
not available.
Heat Level button, Display and Icons
Not all programmes allow you to change the heat level and
some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the display briefly shows
the selected heat level, along with a display of the selected
level icon:
HIGH HEAT
MEDIUM HEAT
LOW HEAT
Sound
Available on all programmes and allows the buzzer to give a
signal at the end of the drying cycle, to remind you that the
clothes are ready to be removed.
Note:
If you have selected the Crease Care option this
option is not available
Extra Care
This Anti-Ageing function for Cottons helps to maintain the
brightness of your laundry for a long time, thanks to the
correct drum rotation (reduced in the last part of the cycle)
and the correct temperature.
Quick Dry
This option is for small loads up to 1kg.
Note:
can only be used with the ‘Cupboard Dry’ setting.
•
TIME DISPLAY
The display shows either the amount of time delay remaining or
an indication of the amount of time left for a drying programme
(see The Display)
. The display also shows if there is a problem
with your dryer, if this occurs the display will show F followed by
a fault code number
(see Troubleshooting)
.
• Empty Water Container
(Messages about emptying can be ignored if you have plumbed
your dryer into a drain as there is no need to empty the water
container). Messages are displayed to reminds you to empty
the water container
(see The Display)
. If the water container fills
during a programme, the heater turns off and the dryer does a
period of Cool Tumble. After this it stops and a message tells
you to
EMPTY THE WATER CONTAINER
. You must empty the water
container and restart the dryer or the clothes will not dry. After
re-starting the dryer the message will take a few seconds to go
out. To avoid this always empty the water container each time
you use the dryer
(see Maintenance)
.
•
Door Opening
Opening the door during a programme will stop the dryer and
have the following effects:
Note:
The
START/PAUSE
light flashes Amber during the
Post Care phase of a programme
� • The display shows
PAUSED
.
�• During a delay phase the delay will continue to count down.
The
START/PAUSE
button
must
be pressed to resume
the delay programme. The display will change to show current
status.
• The
START/PAUSE
button
must
be pressed to resume
the programme. The display will change to show the
current status.
• During the Post Care phase, the programme ends. Pressing
the
START/PAUSE
button will restart a new programme
from the beginning.
�•
Note
If you have a power cut, switch off the power or remove the
plug. When power is restored, press and hold the On/Off
button until the display briefly shows
POWER ON
and the dryer
reactivates. Then press the
START/PAUSE
button and the
programme will resume.
Start and Programmes
Troubleshooting
Possible causes / Solution:
• The plug is not plugged into the socket, or not making contact.
• There has been a power failure.
• The fuse has blown. Try to plug another appliance into the socket.
• You are using an extension cord? Try to plug the dryer’s power cord directly into the
socket.
• The door is not closed securely?
• The programme has not been set properly
(see Start and Programmes)
.
• The Start/Pause button has not been pressed
(see Start and Programmes).
• You have set a delayed time
(see Start and Programmes).
• The filter has not been cleaned
(see Maintenance)
.
• The water container needs emptying? The empty water message is displayed?
(see
Maintenance)
.
• The heat pump filter needs cleaning?
(see Maintenance)
.
• The temperature setting is not ideal for the type of fabric you are drying
(see Start
and Programmes, and see Laundry)
.
• The correct drying time has not been selected for the load
(see Laundry)
.
• The air intake grille is obstructed
(see Installation, and see Maintenance)
.
• The items were too wet
(see Laundry).
• The dryer was overloaded
(see Laundry)
.
• The water container was probably not emptied at the start of the programme. Do not
wait for the empty water signal, always check and empty the container before starting
a new drying programme
(see Maintenance)
.
• This is normal, the:
message is shown as a reminder to empty the container
(see The Display and Start
and Programmes)
.
!
For safety the dryer has a maximum programme time of 5 hours. If an automatic
programme has not sensed the required final moisture in this time the dryer will
complete the programme and stop. Check the above points and run the programme
again, if the results are still damp, contact the Service Centre
(see Service)
.
• If the display shows a fault:
- Turn off and remove the plug. Clean the filter and the heat pump filter unit
(see
Maintenance).
Then replace the plug, turn on and start another programme. If a fault
is then displayed: Note down the code and contact the Service Centre
(see Service)
.
• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause
buttons for 3 seconds. The display will show
DEMO OFF
for 3 seconds and then the
dryer will resume normal operation.
• The dryer has gone into standby mode to save power. This occurs if you have had a
power cut or leave your dryer either without starting a programme or after your drying
programme has finished.
- Press and hold the On/Off button and the lights will come on.
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water message is displayed but
the dryer has only been running for a
short period.
Empty water message is displayed and
the water container is not full.
Programme finishes and clothes are
damper than expected.
The display shows a fault
code F followed by one or two
numbers.
The display briefly shows
DEMO ON
every 6 seconds.
The lights on the dryer control
panel are off although the
dryer is switched on.
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following
troubleshooting suggestions:
END OF CYCLE, CLEAN FILTER AND EMPTY THE WATER BOTTLE
