background image

GB

5

*

 

Only available in selected models.

Electrical connection

Before inserting the plug into the electrical socket, make 
sure that:

•  The  socket  is 

earthed

 

and complies with current 

regulations;

•  the  socket  can  withstand  the  maximum  load  of  the 

appliance as shown on the data plate located on the inside 
of the door 

 

(see chapter Description of the appliance);

•  The power supply voltage falls within the values indicated 

on the data plate on the inside of the door.

•  The socket is compatible with the plug of the appliance. If 

this is not the case, ask an authorised technician to replace 

the plug (

see After Sales Service

). Do not use extension 

cables or multiple sockets.

Once the appliance has been installed, the power supply 

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced 

by the manufacturer or its authorised Technical Assistance 
Service in order to prevent all potential hazards. 

(See After 

Sales Service)

The Company shall not be held responsible for any 

incidents, if these regulations are not observed. 

This appliance must be earthed.

Fuses:your appliance comes fitted with a plug and a 13A fuse. If 
you need to replace the fuse, only those rated at 13A and ASTA 
approved to BS1362 should be used. If you lose the fuse cover, a 
replacement may be obtained from your local authorised Service 

Centre or Electrical company. Correct replacement is identified 

by colour coding or the marking on base of plug.
DO NOT use the plug unless the fuse cover is fitted.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your 

socket.

To avoid a shock hazard DO NOT insert the discarded plug 
into a socket anywhere else.

Wires in the mains lead are coloured accordance with the 

following code:

Green/Yellow      - 

Earth

Blue 

 

  - 

Neutral

Brown   

  - 

Live

If you change the plug, the colour of the wires in the mains lead 
may not correspond with the terminal markings in the plug, which 
if not coloured, could be:

EARTH  ‘E’   or
NEUTRAL 

‘N’

LIVE 

 

‘L’ 

Advice regarding the first wash cycle

After the installation, remove the stoppers from the racks and 
the retaining elastic elements from the upper rack

 (if any).

Water softener settings

Before starting the first wash cycle, set the hardness lev-
el of 

the water from the mains supply. 

(see chapter Rinse aid 

and refined salt).

First load the softener tank with water, then introduce about 
1 kg of salt. It is perfectly normal for water to flow out.
As soon as this procedure is complete, run a wash cycle.
Only use salt that has been specifically designed for dish-
washers.
After the salt has been poured into the machine, the LOW 
SALT indicator light

*

 switches off.

If the salt container is not filled, the water softener and the 

heating element may be damaged as a result.

Changing the Mains Lead

A lead can be ordered from Hotpoint Service

UK: 08709 066 066 or

Republic of Ireland: 1850 302 220

- If you have damaged the existing lead or require a longer one 

a charge will be made.  It is strongly advised that this work is 

carried out by a qualified electrician.

- If the domestic wiring includes a residual current-operated 
circuit breaker, ensure that it conforms to the latest regulations.

 The dishwasher must not be connected to the electricity supply 
while installation is being carried out.
- This appliance should only be connected to a 230/240V AC 
source, via a properly installed earthed socket.

- Use the dishwasher solely in a domestic environment.

- DO NOT stand or place heavy objects on the door when it is 
open, this could damage the door or cause the appliance to tip 
forward.

Summary of Contents for FDUD 44110ULTIMA





















Reviews: