Hotpoint Ariston VS S15 AAW, Operating Instructions Manual, Page: 19 / 45

19
it en
Water
hardness
[°f]
Ratio
[Tap water : de-mineralized water]
<25° f 1:0
25°f – 35°f 2:1
35°f – 50 °f 1:1
50°f – 75°f 1:2
>75°f 0:1
3. Carefully close the tank cover (6).
4. Pull and turn the top cable-winder support to
completely unwind the cable.
Before you connect the plug to the wall socket,
please completely unwind the power cable in
order to avoid its overheating or to avoid damaging it.
It could be useful to vacuum the loor before
you use the device in steam mode.
5. Please position the cloth under the steam
cleaning tool (16) and then the device on it.
6. Connect the plug to the wall socket (220-240V).
7. Turn the power electronic regulator anticlockwi-
se (3) in order start the device in steam mode.
Position the power electronic regulator so that it
is in line with the symbol
Before you start using the device, wait for it to
heat up (20 seconds).
8. Select the amount of steam you want (according
to the surface to be cleaned) by acting on the
steam selection button (4)
9. Move the device as if were a standard brush.
The device emits steam only when it is not in its
rest position; this is particularly useful to limit
steam emissions thus avoiding to damage delicate
surfaces (such as parquets) during interruptions.
Quando pulite superici delicate vi raccomandiamo
di utilizzare una quantità di vapore bassa. When
cleaning delicate surfaces please use a limited
amount of steam.
Please use a large amount of steam to remove
persistent stains.
10.
In order to turn off the device, please turn
the power electronic regulator clockwise by
positioning it in line with the Off symbol.
11. Let the device cool down for about 3-5 minutes
on the carpets tool (17) before you put it back.
After being used, the device is hot and the
cloth is wet. Pay attention! Do not damage
delicate loors!
12. Wind up the cable.
13. Remove the cloth.
2.
Insert the ixing screw and irmly fasten it.
3.
Insert the dust container (2) in its housing, by
positioning irst in the upper part and then in
the lower part until you hear the click of “closing
complete”.
USE OF THE VACUUM MODE (B)
Do not use the device without ilters (14) or
without the dust container (2), ad it could get
damaged.
1. Unwind the power cable (12) and insert the plug
of the device in a wall socket (220-240V).
Before you connect the device to the electri-
cal plug, please unwind all the power cable
to avoid its heating up and avoid damaging it.
2. Use the device with one brush only (1).
3. Turn the power electronic regulator clockwise (3)
in order start the device in vacuum mode. Posi-
tion the power electronic regulator so that it is in
line with the symbol. .
4.
In order to turn off the device, please turn the
power electronic regulator anticlockwise by
positioning it in line with the Off symbol.
5. Wind the cable around the top cable-winder
support (10) and the bottom cable-winder
support (11).
USING THE STEAM MODE (C)
Never use the device without a cloth as this
could damage the device itself as well as the
loor.
Unplug the plug before you ill in the tank.
1. Open the tank lid (6).
2.
Use the illing bottle (15) to ill the tank (5).
The “MAX” level which is shown on the bottle
corresponds to the maximum capacity of the
tank (550 ml). Do not overill the tank.
In order to guarantee a safe usage of the device,
please do not add chemicals to the tank.
In order to extend the device working life, if you
live in an area with an high level of water
hardness, please mix tap water with de-mineralized
water according to the data provided in the following
table: