EN
23
Rinse aid and refined salt
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to
add rinse aid; however,
we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
Follow the instructions given on the packaging.
If you do not add salt or rinse aid, the LOW
SALT
*
and LOW RINSE AID
*
indicator lights
remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
When the LOW RINSE AID
*
indicator light on the control
panel/dislay is illuminated;
1. Open the dispenser by turning
the lid (G) in an anticlockwise
direction.
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a dry
cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from your local water supplier.
- Switch on the appliance by pressing the
ON/OFF
button.
- Press the
P
button and hold for approximately 5 seconds;
two short beeps will sound, the text
H2O
will appear on the
display and the set hardness number will flash (the water
softening system is set by default to number 3). Press the
P
button repeatedly until the desired hardness level has been
reached (1-2-3-4-5
*
see Water hardness table
), up to a
maximum of five levels.
- To exit the function, wait a few seconds or press one of the
option buttons
*
, or switch off the machine using the
ON/OFF
button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty.
Refined salt removes limescale from the water, thus
avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher (
see Description
) and should be filled:
When the green float
*
cannot be seen by simply looking at
the cap of the salt dispenser.
When the LOW SALT
*
indicator light on the control panel/
display is illuminated;
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. The first time you do this: fill the water
tank right up to its edge.
3. Position the funnel
*
(
see figure)
and fill
the salt container right up to its edge (this should hold
approximately 1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel* and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it
on, the head facing downwards so as to let the water flow out
of the four cracks which are arranged in a star shape on the
lower part of the cap. (Salt cap with green float
*
)
It is advisable to perform this procedure every time you
add salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
*
Only available in selected models.
G
F
Water Hardness Table
°dH
°fH mmol/l level
0 6 0 10 0 1
1
6 11 11 20 1.1 2
2
12 17 21
30 2.1
3
3
17 34 31 60 3.1 6
4
34 50 61 90 6.1 9
5
*
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
