14
GB
F
itting
the
po
w
er
s
u
ppl
y
ca
b
le
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(
see diagram
).
2. Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3. Remove the wire
contact screws L-N-
, then fasten the wires
under the screw heads,
respecting the colour
code: Blue (N), Brown
(L) and Yellow-Green
Verde (
).
C
onne
c
tin
g
t
h
e
ele
c
tri
c
it
y
s
upp
l
y
c
a
b
le
to
t
h
e
m
ains
Install a standardised plug corresponding to the
load indicated on the data plate (
see table
).
The appliance must be directly connected to the
mains using an omnipolar circuit-brea
k
er with a
minimum contact opening of 3 mm installed between
the appliance and the mains. The circuit-brea
k
er
must be suitable for the charge indicated and must
comply with current electrical regulations (the
earthing wire must not be interrupted by the circuit-
brea
k
er). The supply cable must be positioned so
that it does not come into contact with temperatures
higher than 50°C at any point.
The installer must ensure that the correct electrical
connection has been made and that it is fully
compliant with safety regulations.
Before connecting the appliance to the power
supply, ma
k
e sure that:
The appliance is earthed and the plug is compliant
with the law.
The soc
k
et can withstand the maximum power of
the appliance, which is indicated on the data
plate (
see below
).
The voltage is in the range between the values
indicated on the data plate (
see below
).
The soc
k
et is compatible with the plug of the
appliance. If the soc
k
et is incompatible with the
plug, as
k
an authorised technician to replace it.
D
o not use extension cords or multiple soc
k
ets.
Once the appliance has been installed, the power
supply cable and the electrical soc
k
et must be
easily accessible.
The cable must not be bent or compressed.
The cable must be chec
k
ed regularly and replaced
by authorised technicians only.
Th
e
m
an
u
f
a
c
t
u
rer
d
e
c
lines
an
y
lia
b
ilit
y
s
h
o
u
l
d
t
h
ese
sa
f
et
y
m
eas
u
res
not
b
e
o
b
ser
v
e
d
.
TABLE
O
F
CHARACTERISTICS
Dimensions
w
idth
43.5
cm
height
32
cm
depth
40
cm
Volume
56
l
Electrical
connections
voltage:
230V
~
50Hz
/
maximum
power
absorbed
2800W
ENERGY
LABEL
Directive
2002/40/EC
on
the
label
of
electric
ovens.
Regulation
EN
50304
Energy
consumption
for
Natural
convection
heating
mode:
=
Traditional
mode;
Declared
energy
consumption
for
Forced
convection
Class
heating
mode:
K
Baking
mode.
This
appliance
conforms
to
the
following
European
Economic
Community
directives:
2006/95/EEC
dated
12/12/06
(Low
Voltage)
and
subsequent
amendments
-
89/336/EEC
dated
03/05/89
(Electromagnetic
Compatibility)
and
subsequent
amendments
-
93/68/EEC
dated
22/07/93
and
subsequent
amendments.
2002/96/EEC
