1
5
GB
DATA PLATE
Dimensions
width 43.5 cm
height 32 cm
depth 40 cm
Volume
56 l
Dimensions
*
width 43.5 cm
height 32 cm
depth 41.5 cm
Volume
*
58 l
Electrical
connections
voltage: 220-230V~ or 220-230V~
50Hz
maximum power absorbed 2800W
(see data plate)
ENERGY LABEL
Directive 2002/40/EC on the label
of electric ovens.
Norm EN 50304
Energy consumption for Natural
convection – heating mode:
Traditional mode
Declared energy consumption for
Forced convection Class – heating
mode: Baking
This appliance conforms to the
following European Economic
Community directives:
-2006/95/EEC of 12/12/06 (Low
Voltage) and subsequent
amendments;
- 89/336/EEC of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments;
- 93/68/EEC of 22/07/93 and
subsequent amendments.
- 2002/96/EC
*
W
it
h
glass
panel
f
itte
d
to
t
h
e
insi
d
e
o
f
t
h
e
d
oor
E
le
c
t
r
i
c
al
c
onne
c
tions
!
Ovens equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the data plate located on the appliance (
see below
).
F
ittin
g
t
h
e
p
o
w
er
s
u
pp
l
y
c
a
b
le
1. Open the terminal
board by inserting a
screwdriver into the side
tabs of the cover. Use
the screwdriver as a
lever by pushing it down
to open the cover (
see
diagram
).
2. Loosen the cable
clamp screw and remove
it, using a screwdriver as
a lever (see figure).
3. Remove the wire
contact screws L-N- ,
then fasten the wires
under the screw heads,
respecting the colour
code: Blue (N), Brown (L)
and Yellow-Green Verde
( ).
C
onne
c
tin
g
t
h
e
s
u
pp
l
y
c
a
b
le
to
t
h
e
mains
Install a standardised plug corresponding to the
load indicated on the data plate (
see side
).
The appliance must be directly connected to the mains
using an omnipolar circuit-brea
k
er with a minimum
contact opening of 3 mm installed between the
appliance and the mains, suitable for the load indicated
and complying with current electrical regulations (the
earthing wire must not be interrupted by the circuit-
brea
k
er). The supply cable must not come into contact
with surfaces with temperatures higher than 50°C.
!
The installer must ensure that the correct electrical
connection has been made and that it is compliant
with safety regulations.
Before connecting to the power supply, ma
k
e sure that:
The appliance is earthed and the plug is
compliant with the law.
The soc
k
et can withstand the maximum power of
the appliance, which is indicated on the data
plate (
see below
).
The voltage must be in the range between the
values indicated on the data plate (
see below
).
The soc
k
et is compatible with the plug of the
appliance. If the soc
k
et is incompatible with the
plug, as
k
an authorised technician to replace it.
D
o
not use extension cords or multiple soc
k
ets.
!
Once the appliance has been installed, the power
supply cable and the electrical soc
k
et must be
easily accessible.
!
The cable must not be bent or compressed.
!
The cable must be chec
k
ed regularly and replaced
by authorised technicians only (
see Assistance
).
! The manufacturer declines any liability should
these safety measures not be observed.
