background image

2

 WARNING

Only qualified service technicians should install and service the appliance. To 
obtain the name and phone number of your local Hoshizaki Certified Service 
Representative, visit www.hoshizaki.com. No service should be undertaken until 
the technician has thoroughly read this Service Manual. Failure to service and 
maintain the appliance in accordance with this manual will adversely affect safety, 
performance, component life, and warranty coverage and may result in costly water 
damage. Proper installation is the responsibility of the installer. Product failure or 
property damage due to improper installation is not covered under warranty.

Hoshizaki provides this manual primarily to assist qualified service technicians in the 
service of the appliance. 

Should the reader have any questions or concerns which have not been satisfactorily 
addressed, please call, send an e-mail message, or write to the Hoshizaki Technical 
Support Department for assistance.

Phone: 1-800-233-1940; (770) 487-2331
Fax: 1-800-843-1056; (770) 487-3360

E-mail: [email protected]

618 Highway 74 South
Peachtree City, GA 30269
Attn: Hoshizaki Technical Support Department

Web Site: www.hoshizaki.com

NOTE: 

To expedite assistance, all correspondence/communication MUST include the 

following information:

• Model Number                                                        

• Serial Number                                                         

• Complete and detailed explanation of the problem.

Summary of Contents for KMS-1122MLJ


























































Reviews: