background image

6

I. Specifications

A. Electrical and Refrigerant Data

The rating label and nameplate provide electrical and refrigerant data. The rating label 
can be seen by removing the front panel. The nameplate is located on the rear panel. For 
certification marks, see the nameplate.
We reserve the right to make changes in specifications and design without prior notice.

1. KM-350M_J

Single Phase

Model Number

KM-350MAJ

KM-350MWJ

AC Supply Voltage

115/60/1

115/60/1

Compressor

115V 7.5RLA    50LRA 115V 6.8RLA   50LRA

Pump

120V 0.4FLA   10W

120V 0.4FLA   10W

Fan

115V 1.0FLA 1/15 HP

--- --- ---

Other

115V 0.15A

115V 0.15A

Maximum Fuse Size 15 AMPS

15 AMPS

Max. HACR Breaker 
(USA Only)

15 AMPS

15 AMPS

Max. Circuit Breaker 
(Canada Only)

15 AMPS

15 AMPS

Minimum Circuit 
Ampacity

15 AMPS

15 AMPS

Design Pressure

HI-467PSI LO-250PSI HI-427PSI LO-250PSI

Refrigerant

404A 1 LB. 3.4 OZ.

404A  11.6 OZ.

2. KM-520M_J(Z)

Single Phase

Model Number

KM-520MAJ

KM-520MWJ

KM-520MRJZ

AC Supply Voltage

115/60/1 

115/60/1 

115/60/1 

Compressor

115V 8.9RLA 54.5LRA

115V 7.8RLA 54.5LRA

115V 8.4RLA 54.5LRA

Pump

120V 0.5FLA 10W

120V 0.5FLA 10W

120V 0.5FLA 10W

Fan

120V 1.0FLA 1/15 HP

--- --- ---

120V 3A MAX 

Other

115V 0.15A

115V 0.15A

115V 0.15A

Maximum Fuse Size 20 AMPS

20 AMPS

20 AMPS

Max. HACR Breaker 
(USA Only)

20 AMPS

20 AMPS

20 AMPS

Max. Circuit Breaker 
(Canada Only)

20 AMPS

20 AMPS

20 AMPS

Minimum Circuit 
Ampacity

20 AMPS

20 AMPS

20 AMPS

Design Pressure

HI - 467PSI  LO - 250PSI HI - 427PSI  LO - 250PSI HI - 467PSI  LO - 250PSI

Refrigerant

404A 1 LB 10.8 OZ.

404A 12.7 OZ.

R404A 
Total Refrigerant Charge with 
Hoshizaki Remote Condenser 
Unit URC-5FZ: 4 LB. 2.7 OZ.

Summary of Contents for KM-520MRJZ










































Reviews: