Hoshizaki KM-520MRJZ Instruction Manual Download Page 14 | Manualshive

Page: 14 / 41

background image

14

D. Setup

1. Dispenser Unit/Ice Storage Bin and Icemaker Setup

WARNING

• The installer must ensure the dispenser unit/ice storage bin is compatible with

the icemaker, and the dispenser unit/ice storage bin and icemaker are properly
attached and secured.

• Do not allow top kits to interfere with the bin control lens sensing area or the

icemaker will not operate properly.

1) If mounting the icemaker on top of a dispenser unit, follow the dispenser unit's setup

procedure. If mounting the icemaker on top of an ice storage bin, unpack the ice storage
bin and attach the 4 adjustable legs provided (bin accessory) to the bottom of the ice
storage bin.

2) Position the dispenser unit/ice storage bin in its permanent location.
3) If required, install an adapter kit or top kit. Contact your local Hoshizaki distributor for

recommendations.

4) Level the dispenser unit/ice storage bin in both the left-to-right and front-to-rear

directions. If using an ice storage bin, adjust the ice storage bin legs to level.

5) Place the icemaker on top of the dispenser unit/ice storage bin.

6a)

Dispenser Unit:

Follow the dispenser unit, adapter kit, or top kit instructions for

securing the icemaker. If no instructions are available, secure the icemaker using the
mounting brackets provided. Rotate the mounting brackets so that they fit flush to the
dispenser unit. See Fig. 2a. Secure the mounting brackets to the icemaker with the bolts
provided. Secure the mounting brackets to the dispenser unit with self-tapping screws
(not provided).

NOTICE!

Use care to avoid damage to dispenser unit components

when attaching the mounting brackets. For dispenser unit bin control setting see
"II.J. Bin Control Check and Setting."

6b)

Ice Storage Bin:

Follow the ice storage bin, adapter kit, or top kit instructions for

securing the icemaker. If no instructions are available, secure the icemaker using the
2 mounting brackets and the bolts provided. See Fig. 2b.

Fig. 2a

Fig. 2b

Icemaker

Dispenser
Unit

Self-Tapping
Screws
(Not Provided)

Bolts

Mounting

Brackets

Icemaker

Ice

Storage

Bin

Mounting

Brackets

Bolts

«
...
12
13
14
15
16
...
»

Summary of Contents for KM-520MRJZ










































Reviews:

No comments

Related manuals for KM-520MRJZ

Brand: Gaggia Pages: 4

Brand: Unic Pages: 2

Brand: Quality Espresso Pages: 16

Brand: Buffalo Pages: 36

Nescafe Dolce Gusto

Brand: T-Fal Pages: 40

Brand: Omcan Pages: 16

Brand: Unimark Pages: 43

VELASCA PRESTIGE

Brand: Gaggia Pages: 56

GS-3405T Series

Brand: Gainscha Pages: 35

Brand: CTM Pages: 187

Brand: Saeco Pages: 40

Brand: Teka Pages: 118

Brand: Eldom Pages: 34

Brand: Gaggia Milano Pages: 180

Brand: Mr. Coffee Pages: 14

Brand: GE Pages: 20

Brand: GE Pages: 9

Brand: GE Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands