Hoshizaki KM-520MRJZ Instruction Manual Download Page 29 | Manualshive

Page: 29 / 41

background image

29

2. Post-Startup

WARNING

•

CHOKING HAZARD:

Ensure all components, fasteners, and thumbscrews

are securely in place after installation. Make sure that none have fallen into the
dispenser unit/ice storage bin.

• Confirm that all internal and external connections are free of leaks.

1) Has the bin control been set to the proper setting for the application?
2) Has the bin control operation been confirmed?
3) Are all components, fasteners, and thumbscrews securely in place?
4) Has the end user been given the instruction manual, and instructed on how to operate

the appliance and the importance of the recommended periodic maintenance?

5) Has the end user been given the contact information of an authorized service agent?
6) Has the warranty registration been completed and submitted to the factory?

«
...
27
28
29
30
31
...
»

Summary of Contents for KM-520MRJZ










































Reviews:

No comments

Related manuals for KM-520MRJZ

Brand: U-Line Pages: 21

Brand: Profi Cook Pages: 42

Puristika 81025

Brand: ECM Pages: 34

Brand: Ice-O-Matic Pages: 2

Brand: wacaco Pages: 16

Brand: DeLonghi Pages: 18

Brand: Saeco Pages: 88

Brand: FUNAI Pages: 14

Brand: Menuett Pages: 16

Brand: Oki Pages: 250

Brand: CROWNFUL Pages: 12

Brand: Felix Storch Pages: 88

BVMC-JWX12CUP 180024

Brand: Mr. Coffee Pages: 28

Brand: Clatronic Pages: 39

Brand: Brandt Pages: 23

Brand: KitchenAid Pages: 22

Brand: KitchenAid Pages: 28

Compact Coffee Maker

Brand: KitchenAid Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands