Hoshizaki HFE-127MA-CHD Service Manual Download Page 63

Page: 63 / 67

[c] INTERIOR FAN MOTOR (HRFE-77MA)

1) Unplug the unit.

2) Open the door to the refrigerator. Unscrew and remove the cooling duct.

3) Unscrew and remove the interior fan motor assembly.

4) Remove the screws securing the interior fan motor to the bracket, and take off the

interior fan motor.

5) Cut the fan motor leads at their connection. (Keep the lead re-connectable.)

6) Loosen the screws securing the fan cover, and remove the fan cover.

7) Remove the interior fan motor from the air duct.

8) To replace the removed parts, reverse the above procedure.

Note: 1. To prevent water from coming in, the lead terminals

must be caulked and covered with plastic bag. Be

sure to connect the leads outside the unit.

2. Seal the lead hole with putty later.

Fan motor

assembly

Duct

Summary of Contents for HFE-127MA-CHD




































































Search results

Summary of Contents for HFE-127MA-CHD

Reviews:

Related manuals for HFE-127MA-CHD

Brands by name

Popular brands

Hoshizaki HFE-127MA-CHD, Service Manual

Search results

Summary of Contents for HFE-127MA-CHD

Reviews:

Related manuals for HFE-127MA-CHD

Brands by name

Popular brands