Hoshizaki HFE-127MA-CHD Service Manual Download Page 62

Page: 62 / 67

[b] INTERIOR FAN MOTOR (Except HRFE-77MA)

1) Unplug the unit.

2) Disconnect the interior fan motor

connector beside the refrigeration unit.

3) Unscrew the refrigeration unit.

4) Slightly lift up the refrigeration unit, and

put the interior fan motor leads inside

the cabinet.

5) Remove the air duct.

6) Loosen the screws securing the fan

cover, and remove the fan cover.

7) Remove the interior fan motor from the air duct.

8) To replace the removed parts, reverse the above procedure.

Keep the fan 5 mm from the end of the motor shaft as shown.

Cover the interior fan motor leads with the insulation tube as

a cushion through the hole in the refrigeration unit.

Note: To prevent the leads from being caught between the fan

blades, fix the leads with the wire retainer inside the air

duct before fitting the air duct.

Air Duct

Fan Motor

Insulation Tube

Wire Retainer

Fan

Fan Cover

Summary of Contents for HFE-127MA-CHD




































































Search results

Summary of Contents for HFE-127MA-CHD

Reviews:

Related manuals for HFE-127MA-CHD

Brands by name

Popular brands

Hoshizaki HFE-127MA-CHD, Service Manual

Search results

Summary of Contents for HFE-127MA-CHD

Reviews:

Related manuals for HFE-127MA-CHD

Brands by name

Popular brands