manualshive.com logo in svg

Hoshizaki C-80BAJ, Service Manual

Share
Download
Hoshizaki C-80BAJ Service Manual Download Page 3

3

CONTENTS

Important Safety Information ................................................................................................. 4
I. Construction and Water/Refrigeration Circuit Diagram ....................................................... 7

A. Construction .................................................................................................................. 7

1. Icemaker .................................................................................................................. 7
2. Ice Making Assembly ............................................................................................... 8
3. Water/Refrigeration Circuit Diagram ........................................................................ 9

II. Sequence of Operation and Service Diagnosis ............................................................... 10

A. Sequence of Operation Flow Chart   ........................................................................... 10
B. Service Diagnosis ........................................................................................................11

1. Ice Production Check ..............................................................................................11
2. Diagnostic Procedure .............................................................................................11

C. Bin Control Check ....................................................................................................... 14
D. Float Switch Check and Cleaning ............................................................................... 15

1. Float Switch Check ................................................................................................ 15
2. Float Switch Cleaning ............................................................................................ 15

E. Optional Drain Pump HS-5061 .................................................................................... 17

1. Overview ................................................................................................................ 17
2. Drain Pump Check ................................................................................................. 17

F. Diagnostic Tables ......................................................................................................... 18

III. Controls and Relays ........................................................................................................ 20

A. Control Switch ............................................................................................................. 20
B. Time Delay Relay ........................................................................................................ 20
C. Water Control Relay .................................................................................................... 20

IV. Refrigeration Circuit and Component Service Information.............................................. 21

A. Refrigeration Circuit Service Information .................................................................... 21
B. Component Service Information .................................................................................. 24

1. Upper Bearing Wear Check  .................................................................................. 26
2. Removal and Replacement of Extruding Head ...................................................... 27
3. Removal and Replacement of Auger ..................................................................... 28
4. Removal and Replacement of Evaporator ............................................................. 29
5. Removal and Replacement of Mechanical Seal and Lower Housing  ................... 30
6. Removal and Replacement of Gear Motor ............................................................ 32

V. Maintenance .................................................................................................................... 33

A. Maintenance Schedule ................................................................................................ 34

VI. Preparing the Appliance for Periods of Non-Use ............................................................ 35
VII. Disposal ......................................................................................................................... 37
VIII. Technical Information .................................................................................................... 38

A. Specification and Performance Data ........................................................................... 38
B. Wiring Diagrams .......................................................................................................... 39

1. C-80BAJ(-DS)(-AD)(-ADDS) .................................................................................. 39
2. Optional Drain Pump HS-5061 .............................................................................. 40

IMPORTANT

This manual should be read carefully before the appliance is serviced. Read 
the warnings and guidelines contained in this manual carefully as they provide 
essential information for the continued safe use, service, and maintenance of the 
appliance. Retain this manual for any further reference that may be necessary.

Summary of Contents for C-80BAJ









































Reviews:

No comments

Brands by name

Popular brands

Load more brands