manualshive.com logo in svg

Hoshizaki C-80BAJ, Service Manual

Share
Download
Hoshizaki C-80BAJ Service Manual Download Page 24

24

B. Component Service Information

NOTICE

• When replacing a component listed below, see the notes to help ensure proper 

operation.

• When replacing evaporator assembly and water circuit components, make sure 

there are no water leaks after the repair is complete.

Component

Notes

Extruding Head • Seal bolts must be replaced once removed because seal material is one-time use only.

• If new seal bolts do not have preapplied threadlocker, apply Loctite 243 or equivalent 

threadlocker to seal bolt threads.  

• Tighten down the new seal bolts to a torque of 11.1 ft-lb/15 N·m. 

Compressor

• Install a new drier and PTC relay.

Upper and 

Lower Bearings

• Inspect the upper bearing for wear. See "IV.B.1. Upper Bearing Wear Check." Replace if 

necessary.

• When replacing the upper bearing it is advised to also change the lower bearing at the 

same time.

Evaporator

• Install a new drier.
• Inspect the mechanical seal and O-ring prior to installing the new evaporator. If worn, 

cracked, or scratched, the mechanical seal should also be replaced.

Gear Motor

• Install a new gear motor capacitor.

Top Panel

C-80BAJ-AD Shown

Evaporator Assembly

Upper Rear Panel

Top Panel Bracket

Fig. 4

Summary of Contents for C-80BAJ









































Reviews:

No comments

Brands by name

Popular brands

Load more brands