Manual
of
Brushless Motor Speed Controller
Page 1 of 2
-
Features:
1.
Use top quality components to get strong current endurance.
2.
Low voltage cut-off protection / over-heat protection / throttle signal loss protection.
3.
Throttle range can be configured to be compatible with all transmitters.
4.
Maximum motor speed: 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
Specifications:
Size
2S Lipo
3S Lipo
Lipo
NiMH
L*W*H
20A
20A
20A
25A
Linear
5V/2A
5 servos
4 servos
2-3S
5-9 cells
19g
42*25*8
40A
40A
40A
55A
Linear
5V/3A
5 servos
4 servos
2-3S
5-9 cells
35g
68*25*8
Weight
Battery Cell
Class
Model
Cont.
Current
Burst
Current
(>10s)
BEC
Mode
BEC
Output
BEC Output Capability
40A 40A Ubec 40A 55A Switch 5V/4A 5 Servos 5 Servos 2-4S 5-12 Cells 43g 65*25*12
Begin To Use Your New ESC
IMPORTANT!
Because different transmitter has different throttle range, please calibrate throttle range before flying.
How to set the throttle range and how to use the throttle stick to program the
“Brake” function?
1.
Move the throttle stick to the top (highest) position, and then connect battery pack to the ESC, You will hear 1 low, long tone to
indicate startup, then the respective number of medium-length mid-tones to indicate the cell count .
2.
After 2 seconds, the motor sounds
2 long beeps (B
—B—)
, which means the highest position of the throttle range is already
recognized by the ESC (After the beeps, if the throttle stick is moved to the lowest position in 2 seconds, the ESC will recognize the
lowest position, quit the throttle range calibrating process and get ready to start).
3.
After 2 seconds, the motor sounds
a short beep (B) after a music
, which means the Brake function is
Disabled
(After the beep, if
the throttle stick is moved to the lowest position in 2 seconds,
the ESC will recognize the Brake function is disabled
, quit the
programming mode and get ready to start).
4.
After 2 seconds, the motor sounds
2 short beeps (BB)
, which means the Brake function is
Enabled
(After the beeps, if the throttle
stick is moved to the lowest position in 2 seconds,
the ESC will recognize the Brake function is enabled
, quit the programming
mode and get ready to start).
5.
After 2 seconds, the ESC stops running.
How to start the ESC?
Move the throttle stick to the lowest position, and then connect battery pack to the ESC, You will hear 1 low, long tone to indicate
startup, then the respective number of medium-length mid-tones to indicate the cell count, followed by 3 rising tones to indicate the
ESC is armed.
Protection Function
1.
Start up failure protection: If the motor fails to start within 2 seconds of throttle application, the ESC will cut-off the output power. In
this case, the throttle stick
MUST
be moved to the bottom again to restart the motor. (Such a situation happens in the following
cases: The connection between ESC and motor is not reliable, the propeller or the motor is blocked, the gearbox is damaged, etc.)
2.
Over-heat protection: When the temperature of the ESC is over about 110 Celsius degrees
,
the ESC will reduce the output power.
3.
Throttle signal loss protection: The ESC will reduce the output power if throttle signal is lost for 1 second, further loss for 2 seconds
will cause the output to be cut-off completely.
Trouble Shooting
Trouble
Possible Reason
Action
After power on, motor does not work, no
sound is emitted
1
，
The connection between battery
pack and ESC is not correct
2
，
Throttle signal is irregular
；
3
，
The throttle stick is not in the
bottom (lowest) position
Check the power connection.
Replace the connector.
Check the receiver and transmitter
Check the cable of throttle channel
Move the throttle stick to bottom position
After power on, motor does not work,
such an alert tone is emitted:
“beep-beep-, beep-beep-,beep-beep-”
(Every
“beep-beep-” has a time interval
of about 1 second)
Input voltage is abnormal, too high
or too low.
Check the voltage of battery pack
