background image

15

EN

 

Low Voltage Cutoff  (LVC)

Once the battery reaches 3V under load, the ESC will continuously lower power supplied to the motor until complete 
shutdown occurs. This helps prevent over-discharge of the Li-Po battery. Land immediately once the ESC activates LVC. 
Continuing to fl y after LVC can damage the battery, cause a crash or both. Crash damage and batteries damaged due to 
over-discharge are not covered under warranty.

Repeatedly fl ying the aircraft until LVC activates will damage the fl ight battery. 

Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. During storage, make 
sure the battery charge does not fall below 3V per cell. 

While attempting to establish a low-level hover, check to see if any trim adjustments are required to help keep the 
quadcopter from constantly drifting in various directions. If you fi nd that it constantly drifts without any directional control 
input, land the model before making any adjustments to the trim settings.

• If the nose of the quadcopter rotates to the left or right, adjust the rudder trim.
• If the quadcopter continually drifts forward or backward, adjust the elevator trim.
• If the quadcopter continually drifts to the left or right, adjust the aileron trim.

Continue making minor trim adjustments until the machine hovers at a low altitude with very little drifting and directional 
control input. If this is your fi rst multicopter or helicopter, seek the help of an experienced pilot to trim the model for you 
before making your fi rst fl ight.

With your quadcopter properly trimmed and maintaining a stable low-level hover, practice using the rudder, elevator and 
aileron controls to familiarize yourself with the machine’s responses to control inputs. Remember to keep the control 
inputs as minimal as possible.

NOTICE:

 Crash damage is not covered under warranty.

Camera Control and App Function

•  Download and install the Glimpse app to your 5.8 GHz Wi-Fi capable smartphone or tablet by searching for “Glimpse” 

at the Apple App Store for your iOS device or at Google Play for your Android device.

•  Power on your transmitter and the Glimpse.
•  Open the Wi-Fi settings on your smartphone or tablet and connect to the Glimpse network (Glimpse_######) using the 

password “12345678”.

•  Open the Glimpse App on your smartphone or tablet.
•  Place your smartphone in the transmitter holder as shown.
•  Use the onscreen controls as shown on the following page to take photos and video.

Summary of Contents for Blade Glimpse

























Reviews: