Horizon Fireplaces Edge HCLC/P/L1100 Installation Instructions Manual Download Page 19

Page: 19 / 22

24/02/2021

Ver. 5

DIRECT IGNITION

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

PILOT WILL NOT LIGHT

1) NO GAS

- CHECK FOR GAS SUPPLY AND

TURN ON ALL CONNECTIONS

- CHECK GAS PRESSURE
- CHECK PILOT AND CLEAN INJECTOR

2) NO SPARK AT PILOT

- CHECK ELECTRIC SUPPLY AND

TURN ON ALL SWITCHES

- CHECK ALL CONNECTIONS

- CHECK SPARK ELECTRODE CONNECTIONS

AND REPLACE ELECTRODE IF DAMAGED.

- CHECK SOLENOID CONNECTIONS AT VALVE

PILOT LIGHTS BUT

1) FLAME SENSOR NOT

- CHECK ELECTRODE IS IN PILOT

VALVE DOES NOT OPEN TO LIGHT MAIN
BURNER

SENDING SIGNAL TO OPEN

VALVE

FLAME

- CHECK ELECTRODE CONNETCTIONS

- CLEAN ELECTRODE
- CHECK ELECTRODE FOR DAMAGE
- REPLACE ELECRODE

2) MODULE NOT SENDING

- REPLACE MODULE

SIGNAL TO OPEN VALVE

3) FAULTY VALVE

- REPLACE VALVE

FLAME FAIL LOCKOUT

1) POWER FAILURE

- TURN ON/OFF SWITCH OFF AND

UNIT HAS DETECTED LOSS OF FLAME

AND LOCKED OUT

ON AGAIN TO RESET ONCE POWER
ESTABLISHED

2) GAS SUPPLY

- CHECK GAS PRESSURE AND ADJUST

- RESET AT ON/OFF SWITCH

3) DIRTY ELECTRODE

- CLEAN ELECTODE OR REPLACE

4) PILOT BLOCKED

- CLEAN PILOT INJECTOR

5) PRESSURE SWITCHES

NOTE: TECHRITE IGNITION PACK FLASH CODES
(RED LED) TO IDENTIFY PROBLEM.

Installation Instructions Kemlan Natural Draft Horizon Edge Gas Fireplaces

Summary of Contents for Edge HCLC/P/L1100























Search results

Summary of Contents for Edge HCLC/P/L1100

Reviews:

Related manuals for Edge HCLC/P/L1100

Brands by name

Popular brands

Horizon Fireplaces Edge HCLC/P/L1100, Installation Instructions Manual

Search results

Summary of Contents for Edge HCLC/P/L1100

Reviews:

Related manuals for Edge HCLC/P/L1100

Brands by name

Popular brands