background image

  

5  

Use your body as a “torsion spring”: Draw the model from behind of your back. Unwind before the launch and in 
the last launch phase twist the body and move your arm. 
 
Move the CG and trim the elevator, so that the model climbs mildly. Play also with the CG position so that the

 

amount of the inherent stability suits your flying style: these models fly at low heights and often must cope with lots 
of turbulent air. Larger amount of longitudinal stability provided by more forward CG position can be of advantage. 
 
The wing flaps are in neutral position for launch and fast flights while hunting for thermals and for rapid returns 
from downwind distances.  
The  ”neutral position” is with flat wing surface bottom. 
For the low sinking rate deploy the flaps about 3 mm down (measured in the wing centre). Deploy the flaps about 
40 deg down for escape from height and landing. The directional control with fully deployed flaps should be done 
with rudder rather than with ailerons. The model with flaps full down slows down. When moved rapidly back to the 
neutral position, the model can stall because the velocity is too low for the wing in this configuration. 
 

Important notes: 

 

 

NEVER launch model 

if there are persons 

in front of you!!! Remember, the velocity of the model can be close 

to 150 km/hour 

 

If released too early, the model can fly low over the ground, to the right side (right hander). BE ALWAYS SURE 
there are no persons in this segment!!! 

 

Secure the receiver crystal in place with adhesive tape. Otherwise, it can slip out of the socket due the launch 
acceleration!!! 

 

Do not launch model in weeds taller than about knee-height. You would easily damage the outer wing tip. 

 

Before the first flying, make the test range of the RC set. The carbon used for the fuselage can influence the 
signal reception. If you do not have the 2,4 GHz set, the “old fashioned” antenna between receiver and fin tip 
still works best. 

 
For the assembly pictures see 

www.horejsi.cz

 

The video sequence showing launch of one of the best German flyers, Alex Wunschheim, can be downloaded 
from the same site. With kind permission of Alex. 

 
Have a joy with your new LONG SHOT 3! 
Horejsi model Ltd. 
Czech Republic 

 

Summary of Contents for Long Shot 3






Reviews: