HopeRF RF 65 Manual Download | Manualshive

Page: 43 / 72

background image

Page 43

RF65

Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com

ADVANCED COMMUNICATIONS & SENSING

DATASHEET

5.4. Continuous Mode

5.4.1. General Description

As illustrated in Figure 25, in Continuous mode the NRZ data from the demodulator is directly accessed by the uC on the
DIO2/DATA pin. The FIFO and packet handler are thus inactive.

Rx

CONTROL

DIO0

DIO1/DCLK

DIO2/DATA
DIO3
DIO4
DIO5

Data

Rx

SYNC
RECOG.

SPI

NSS

SCK
MOSI
MISO

Figure 25. Continuous Mode Conceptual View

5.4.2. Rx Processing

If the bit synchronizer is disabled, the raw demodulator output is made directly available on DATA pin and no DCLK signal
is provided.

Conversely, if the bit synchronizer is enabled, synchronous cleaned data and clock are made available respectively on
DIO2/DATA and DIO1/DCLK pins. DATA is sampled on the rising edge of DCLK and updated on the falling edge as
illustrated below.

DATA (NRZ)

DCLK

Figure 26. Rx Processing in Continuous Mode

Note

in Continuous mode it is always recommended to enable the bit synchronizer to clean the DATA signal even if the

DCLK signal is not used by the uC (bit synchronizer is automatically enabled in Packet mode).

«
...
41
42
43
44
45
...
»

Summary of Contents for RF 65









































































Reviews:

No comments

Related manuals for RF 65

Brand: FAAC Pages: 2

Brand: Harman Pages: 30

Brand: RadioMaster Pages: 10

Brand: u-blox Pages: 2

Brand: Uconnect Pages: 70

Brand: Uconnect Pages: 140

Brand: Farenheit Pages: 41

Brand: Audiotech Pages: 7

Brand: Boss Audio Systems Pages: 14

Brand: Axxera Pages: 31

Brand: Delco Pages: 18

Brand: Sennheiser Pages: 50

Brand: Alpine Pages: 38

Brand: Blaupunkt Pages: 4

Brand: X10 Pages: 2

FT DX 9000MP CONTEST - DATA MANAGEMENT OPERATION

Brand: Yaesu Pages: 180

Brand: Harman Kardon Pages: 60

Brand: Kramer Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands