background image

4

Pull switch lock (P) above ON-OFF 

switch (Q) straight out.

Dispose of lock.

Note: If lock has come off during 

assembly, make sure switch is in the 

OFF position (down) before plugging 

cord in to electrical outlet.

Cleaner description

2. How to use

The assembled cleaner will look like the 

drawing.

  1. Handle

  2. ON/OFF switch

  3. Cord hooks: 

wrap cord around hooks 

for storage

  4. Bag cap

  5. Cloth bag

  6. Dirt cup

  7.  Handle release lever: 

step on lever 

to lower handle to operating or low 

position.

  8.  Cleaner body

  9. Furniture guard: 

helps prevent clean-

er from marking furniture.

10. Hood

11. Extra belt storage: 

open door to store 

extra belt.

12. Carpet height control: 

slide knob to 

correct setting for height of carpet 

being cleaned.

Operate cleaner only at voltage specified 

on data plate on bottom of cleaner.
WARNING: electrical shock could occur if 

used outdoors or on wet surfaces.

To reduce the risk of electric shock, this 

appliance has a polarized plug (one blade 

is wider than the other). This plug will fit in 

a polarized outlet only one way. If the plug 

does not fit fully in the outlet, reverse the 

plug. If it still does not fit, contact a quali-

fied electrician to install the proper outlet. 

Do not change the plug in any way.

ON-OFF switch

To turn cleaner ON, push switch up. 

To turn cleaner OFF, push switch down.

1-14

Pull support toward bottom of han-

dle slightly to make sure support is 

locked in place.
Make sure hole in handle (N) is vis-

ible through hole in support.

With cloth bag to the front, place 

assembled handle onto handle base 

of cleaner body.

Rock handle side to side while push-

ing down firmly. Extra pushing effort 

may be required.

Push 

bolt

 into hole on lower 

front of 

handle.

 

If bolt will not go through hole  

easily, handle is not pushed com-

pletely down.

1-15

1-16

1-17

1-18

1-19

Place 

nut (O)

 in recessed area at 

back of handle.

 Hold nut in place 

while tightening bolt securely with a 

screw driver. 

Note:

 Only one nut is needed on this 

model. The extra nut is not required 

but has been provided for your  

convenience.

Reposition dirt cup into support at 

bottom of cloth bag and snap latch-

es into position.

2-1

1

2

3

4

5

6

8

7

9

10

11

O

N

Q

P

12

Summary of Contents for Guardsman C1415





















Reviews: