Honeywell Youjie HH660 User Manual Download | Manualshive

Page: 73 / 164

background image

6 - 1

6

Symbologies

This programming section contains the following menu selections. Refer to

for settings and defaults.

All Symbologies

If you want to decode all the symbologies allowable for your scanner, scan the

All Symbologies On

code. If on the other hand,

you want to decode only a particular symbology, scan

All Symbologies Off

followed by the On symbol for that particular sym-

bology.

Note: Scanner performance may be degraded after scanning

All Symbologies On

. Only scan

All Symbologies On

when

needed.

Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.

Message Length Description

You are able to set the valid reading length of some of the bar code symbologies. You may wish to set the same value for min-
imum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread.

•

All Symbologies

•

Interleaved 2 of 5

•

•

•

China Post (Hong Kong 2 of 5)

•

•

Chinese Sensible (Han Xin) Code

•

•

•

•

•

•

•

•

•

Postal Codes - 2D

•

•

Postal Codes - Linear

•

Code 32 Pharmaceutical (PARAF)

•

•

•

GS1 DataBar Omnidirectional

•

•

•

•

Straight 2 of 5 IATA (two-bar start/stop)

•

•

Straight 2 of 5 Industrial (three-bar start/stop)

•

•

TCIF Linked Code 39 (TLC39)

•

GS1 Composite Codes

•

•

GS1 DataBar Expanded

•

•

GS1 DataBar Limited

•

UPC-A/EAN-13 with Extended Coupon Code

•

GS1 DataBar Omnidirectional

•

•

•

•

All Symbologies On

All Symbologies Off

«
...
71
72
73
74
75
...
»

Summary of Contents for Youjie HH660





































































































































































Reviews:

No comments

Related manuals for Youjie HH660

CanoScan LiDE 120

Brand: Canon Pages: 2

CanoScan LiDE 120

Brand: Canon Pages: 2

Brand: Microtek Pages: 8

Brand: Kodak Pages: 57

Brand: Allen-Bradley Pages: 115

Docking Scanner

Brand: Mustek Pages: 18

Brand: IDTECH Pages: 37

Brand: Motorola Pages: 16

Brand: Motorola Pages: 86

Brand: Motorola Pages: 276

Symbol MiniScan MS1207FZY

Brand: Motorola Pages: 368

Brand: Panasonic Pages: 396

Workio KV-S7065C

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 48

Brand: Scantech Pages: 138

GLS -2000 Series

Brand: Topcon Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands