Honeywell Youjie HH660 User Manual Download

Page: 92 / 164

6 - 20

Coupon GS1 DataBar Output

If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1
DataBar code. Scan the

GS1 Output On

code below to scan and output only the GS1 DataBar code data.

Default = GS1 Out-

put Off.

UPC-E0

<Default All UPC-E Settings>

UPC-E0 On/Off

Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the

UPC-E0 On

selection. If you need to

read codes that lead with the 1 number system, use

UPC-E1

(page 6-22).

Default = On.

UPC-E0 Expand

UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format.

Default = Off.

* GS1 Output Off

GS1 Output On

* UPC-E0 On

UPC-E0 Off

* Off

Summary of Contents for Youjie HH660





































































































































































Search results

Summary of Contents for Youjie HH660

Reviews:

Related manuals for Youjie HH660

Brands by name

Popular brands

Honeywell Youjie HH660, User Manual

Search results

Summary of Contents for Youjie HH660

Reviews:

Related manuals for Youjie HH660

Brands by name

Popular brands