Honeywell Vuquest 3330g User Manual Download

Page: 104 / 201

7 - 20

UPC-A Addenda

This selection adds 2 or 5 digits to the end of all scanned UPC-A data.

Default = Off for both 2 Digit and 5 Digit Addenda.

UPC-A Addenda Required

When

Required

is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or

5 digit addenda listed on

page 7-20

Default = Not Required.

UPC-A Addenda Separator

When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned

off, there is no space.

Default = On.

2 Digit Addenda On

* 2 Digit Addenda Off

5 Digit Addenda On

* 5 Digit Addenda Off

Required

* Not Required

* On

Off

Summary of Contents for Vuquest 3330g










































































































































































































Search results

Summary of Contents for Vuquest 3330g

Reviews:

Related manuals for Vuquest 3330g

Brands by name

Popular brands

Honeywell Vuquest 3330g, User Manual

Search results

Summary of Contents for Vuquest 3330g

Reviews:

Related manuals for Vuquest 3330g

Brands by name

Popular brands